manualshive.com logo in svg

Comet System T0610, Руководство пользователя

Поделиться
Скачать
Comet System T0610 Скачать руководство пользователя страница 34

IE-SNC-Tx6xx-07 

 

 

 34  

Device error states 

Device still make self-tests. If error occurred, LCD shows error codes: 

Error 

LCD display 

Description 

Error 0 

Err0 

Internal memory CRC error. In this state device doesn't work. This is a critical 
error, contact the distributor. 

Error 1 

Err1 

Measured or computed quantity is over the upper limit. Error code 9999. This 
state appears in case of: 

-

 

Measured  temperature  is  higher  than  approximately  +

600°C

  (i.e. 

high  non-measurable  resistance  of  temperature  sensor,  probably 
open circuit) 

-

 

Relative  humidity  is  higher  than  100%RH  (i.e.  damaged  humidity 
sensor  or  humidity  calculation  is  not  possible  due  to  temperature 

error) 

-

 

Unable  to  calculate  computed  quantity  (temperature  or  humidity 
measurement error) 

Error 2 

Err2 

Measured or computed quantity is under lower limit or is error in pressure or 
CO

2

 concentration measuring. Error code -9999. This state appears in case of: 

-

 

Measured  temperature  is  lower  than  approximately  -

210°C  (

i.e. 

resistance is too small, probably short circuit) 

-

 

Relative humidity is lover than 0%RH (i.e. damaged humidity sensor 
or humidity calculation is not possible due to temperature error) 

-

 

Measured atmospheric pressure with offset is over range 300hPa to 
1350hPa or the pressure sensor is damaged 

-

 

CO

2

 concentration measuring error 

-

 

Unable  to  calculate  computed  quantity  (temperature  or  humidity 

measurement error) 

Error 3 

Err3 

Internal A/D converter error. Error code -9999. In this state device doesn't 
work. Contact the distributor. 

Error 4 

Err4 

Internal pressure or CO

2

 concentration sensor error. Error code -9999. In this 

state  device  not  measure  pressure  or  CO

2

  concentration.  Contact  the 

distributor. 

 

Содержание T0610

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды