background image

4

Buttons

   

Audio activation

    Lock-release activation

  Buttons 1-2-3-4-5 (programmable)

   

Self activation (programmable)

   

Ringtone activation in silent mode    

 

 

(Privacy mode)

    Audio volume adjustment

    Call volume adjustment

    Increase / Decrease value

   

Contrast adjustment

   

Brightness control

Indicator LED

   

continuous flashing

 = incoming call

LED steady in call

 = communicating

LED  steady in standby

 = 

Automatic answer

  mode 

(Hands-free mode) enabled

   

continuous flashing

 = incoming call 

1 flash

 = confirm lock-release

4 flashes

 = programming successful

10 flashes

 = programming error

   

LED steady 

= ringtone in 

silent

 mode

 

(Privacy mode)

3 flashes (every 5 s.)

 = 

Automatic door opening on 

receipt of call mode 

 (Doctor mode) enabled

slow flashing

 = programming

4 flashes

 = device busy

Touch-sensitive button activation

 

f

Swipe to enable the row (1) of function buttons.

 

f

Swipe again to enable the row (2) of adjustment buttons.

 

f

Press the desired button once to activate the function 

associated with it

1
2

Press and hold keys 

(Disabled by default from firmware version 1.5.0)

Pressing and holding keys adds further functions to the door entry monitor.

Carry out the procedure described below to enable - or disable, depending on the factory setting - the press and hold 
feature:

 

Door entry monitor in standby.

1. 

Take note of the S2 DIP-switch settings.

2. 

Enter programming mode by setting S2 DIP-switches 1, 3, 5 to ON.

3. 

Press   to enable (or press   to disable).

4. 

Make sure the 

 key flashes 4 times and the confirmation tone is emitted.

5. 

Restore the initial configuration of the S2 DIP-switches.

Once the enabling procedure is complete, you will be able to enable the following functions:

Automatic door opening on receipt of call (Doctor mode)

 

f

Press and hold (4 sec.) the programmed button (default: Key 3) to enable/disable the function.

Automatic answer (Hands-Free function)

 

f

Press and hold (4 sec.) the audio activation button   to enable/disable the function.

Wait for approximately 1 sec. before pressing 

the same button again. Pressing the same 

button several times in quick succession will 

cancel the command.

Содержание Icona Manager


















Отзывы: