background image

 

 

1.5:1 VSWR within foldback limits 

Short Term stability: +/-1%/hr 
Long term stability: +/-5% over three years continuous output 
Zero Setpoint:  less than 5 watts actual output power and less than 5 watts readback 

power when setpoint signal is at zero or at a negative voltage. 

 

NOTE: 

Use RF enable switch (Pins 4-9) 15 Pin D to ensure zero output power.

 

 

B.  Protection Features 

 

1.  Mismatch Protection:  Continuous operation into any impedance mismatch condition 

without damage or malfunction; forward power foldback shall occur within 500us if 
reflected power exceeds 150 Watts. 

 
2.  Output power connection interlock:  Hard-wired interlock that disables the input AC 

power contactor upon removal of the output cable.  

 

3.  Safety interlock: Disables the input AC power contactor via the connector.  MAX external 

loop resistance of 5.0 ohms .  

 

4.  Over Temp Fault:  Output disabled on high internal temperature 

 

5.  Short Circuit Fault:  Output limiting protection under short and open circuit conditions.  

 

6.  Overdrive Limit:  Internally limited at 1100 watts.  

 

7.  Control signal protection:  Unit not to be damaged if a short circuit or up to 30 volts AC or 

DC is placed between any input signal, return signal, and ground. 

 

C.  Generator I/O Requirements 

 

1.  Signal input impedance: 10K ohms, min. 
 
2.  Signal input isolation: 1000 VAC MIN to the A/C supply line. 
 
3.  Line connections:  Linecord to be 14AWG 4 conductor (three phase & ground); linecord 

jacket material to be type "STO" gray; linecord to be crimped to NEMA L15-20P style 
plug; linecord length to be 4.5 ft. +/-6.0 inches as measured from the rear panel exterior to 
the strain relief end of plug.  Reference MARINCO part number 2015P-AM1. 

 

MARINCO:  One Digital Dr. 

Novato, CA 94949 

(415) 883-3347 

 

4.  RF Output power Connector:  One type "N" female coaxial connector 
 
5.  Control connector: 15 pin subminiature "D" type, (female). 
 
6.  Control signals and pinout: 

          

Pin 5:  Power setpoint 

0 to +10 VDC = 0 to 1.0 KW linear 

 
Pin 3:  Forward power out 

0 to +10 VDC = 0 to 1.0 KW linear 

 
Pin 2:  Reflected power out    

0 to +10 VDC = 0 to 1.0 KW linear 

 

Содержание CPS-1001/S/13.56MHZ



















Отзывы: