manualshive.com logo in svg

Comar Systems CSA-300, Инструкция по установке и эксплуатации

Поделиться
Скачать
Comar Systems CSA-300 Скачать руководство пользователя страница 36

Installation

Page 36

Figure 37 Junction box dimensions

Figure 38 Mounting the junction box

4.3.3

Installing the GPS antenna

The CSA-300 AIS transceiver includes an internal GPS receiver for time synchronisation. An independent GPS 
antenna is required for this receiver in addition to any GPS equipment already installed on board.
For mounting of the GPS antenna supplied with your AIS transceiver you will require a one inch 14 TPI pole 
mount. Contact your dealer to source a mount suitable for the installation location. 
Please note the following guidelines when selecting a location for the GPS antenna:

●

The GPS antenna mount should be secured to a rigid surface.

●

The GPS antenna should be located where it has a clear, unobstructed view of the sky overhead.

●

The GPS antenna should be mounted as high as possible, however it is not recommend the antenna 
is mounted on a top of a high mast where the motion of the vessel will cause the antenna to swing 
and potentially reduce the accuracy of the GPS position. See Figure 39 for guidance.

1

78

 

mm

52

 

mm

7

6 

mm

16

5

 

mm

58

 

mm

Содержание CSA-300














































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды