ComAp InteliLite MRS16 Скачать руководство пользователя

Страница: 113 / 632

InteliLite Global Guide

113

Other functions

Consistency check

Use this function to check if all inputs and outputs of PLC block are connected.

Delete whole content of sheet

Use this function to delete the whole content of sheet (including blocks, wires, inputs, outputs, etc...).

Hints

Use this function to enable or disable quick hints for blocks (controller help is not affected by this function).

PLC monitor

PLC monitor is a powerful tool for monitoring your PLC. Just click on PLC monitor button on main LiteEdit2015

page to see you PLC. Active inputs and outputs have blue color. Also wires with active signals have blue color.

IMPORTANT: It is not possible to edit PLC in PLC monitor tool.

5.4.21 Geo-fencing

Geo-fencing function is kind of protection that evaluates whether the actual GPS location is within predefined

area and based on the evaluation takes an action (sends sms, stops engine, make history record etc.). Function

is enabled by setpoint

Geo-Fencing (page 285)

or by logical binary input

Using LiteEdit2015, it is possible to set two concentric geo-circles within which the unit is allowed to be located.

Each geo-circle is defined as circular geographic area with centre (common for both geo-circles) named Home

Position adjusted via setpoints

Home Latitude (page 283)

and

Home Longitude (page 283)

and radius named

Fence Radius adjusted via setpoints .

Fence Radius 1 (page 284)

and

Fence Radius 2 (page 284)

Protections can be different for both circles. Protection are adjusted via setpoints

Fence 1 Protection (page 286)

and

Fence 2 Protection (page 287)

It is also possible to see the current position of the controller in WebSupervisor map view.

5.4.22 Tier 4 Final

Tier 4 Final support generally provides monitoring and control of after-treatment system installed on generators

engine. The requirements are defined as:

Содержание InteliLite MRS16

























































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание InteliLite MRS16

Отзывы:

Похожие инструкции для InteliLite MRS16

Бренды по названию

Популярные бренды

ComAp InteliLite MRS16, Руководство пользователя

Результаты поиска

Содержание InteliLite MRS16

Отзывы:

Похожие инструкции для InteliLite MRS16

Бренды по названию

Популярные бренды