ComAp InteliDrive DCU Marine Скачать руководство пользователя страница 248

Страница: 248 / 285

InteliDrive DCU Marine - 3.0.0 Global Guide

248

Related FW

3.0.0

Related applications

All

Comm object

121

Description

Logical Analog Inputs MainScrAna1 or MainScrAna2 enables to redirect any Analog input value on the ID-

DCU Marine main screen on “OilPress” and “CoolTemp” position.

Note:

Default names “OilPress” and “CoolTemp” do not change when the Logical Analog Inputs

MainScrAna1 or MainScrAna2 are connected to other source values and has to be changed by

translator.

1. Default configuration

ID / AIN_Function = Oil Press; MainScrAna1

ID / AIN2_Function = Coolant Temp; MainScrAna2

2. To display e.g. value from AIN3 “AirTemp1” instead “OilPress” (the first position) and AIN4

“AirTemp2” instead “CoolTemp” value:

a. Select AIN3 Property Function = MainScrAna1

b. Select AIN4 Property Function = MainScrAna2

c. Create new language (in DriveConfig Languages) based on English

d. Rename (in DriveConfig Translator / Other texts) text “OilPress” to “AirTemp1” in the newly

created language

e. Rename (in DriveConfig Translator / Other texts) text “CoolTemp” (no space between) to

“AirTemp2” in the newly created language

f. Switch the ID-DCU Marine controller into newly created and modificated language (Enter +

Page, Page, select the new language by up/down arrows, Enter)

Note:

Translate text “OilPress” and “CoolTemp” - no space between words because of similar texts (e.g.

Coolant Temp, etc. are located on other screens).

MainScrAna2

back to List of LAI

Содержание InteliDrive DCU Marine






























































































































































































































































































Результаты поиска

Содержание InteliDrive DCU Marine

Отзывы:

ComAp InteliDrive DCU Marine, Руководство пользователя, Страница: 248 / 285

Результаты поиска

Содержание InteliDrive DCU Marine

Отзывы: