ComAp InteliDrive DCU Marine Скачать руководство пользователя страница 126

Страница: 126 / 285

InteliDrive DCU Marine - 3.0.0 Global Guide

126

Setpoint group

Engine params

Related FW

3.0.0

Range [units]

CMB, EME: 0 .. 200 [-], AUX, PRP: 1 .. 200 [-]

Default value

Step

Comm object

8255

Related applications

All

Config level

Standard

Setpoint visibility

Always

Description

Max number of crank attempts.

CMB, EME: Setting to 0 means unlimited number of starting attempts.

Note:

There is one start attempt only in case of panel Start button or Binary input Remote Start

activation. Number of Cranking attempts based on this setpoint is accepted when start is activated by

Binary input RemRepStart (PRP) or Blackout Start (AUX, EME and HRB) only. The setpoint is not

followed if Sd Override is active, crank attempts number is then unlimited in case of Blackout Start.

Together with request of unlimited start attempts was created LBI PrestartOverride - activation means

immediate transition from state Prestart to Cranking.

Same function was applied to second push of START button. First press of START button activates state

Prestart, second press of START button skips prestart period.

Crank Attempts

back to List of setpoints

Setpoint group

Engine params

Related FW

3.0.0

Range [units]

Starting RPM.. Nominal RPM [RPM]

Default value

500

Step

Comm object

9946

Related applications

PRP

Config level

Standard

Setpoint visibility

Always

Description

Default Idle speed (should be the same as Idle speed set with engine ECU).

Idle RPM

back to List of setpoints

Содержание InteliDrive DCU Marine






























































































































































































































































































Результаты поиска

Содержание InteliDrive DCU Marine

Отзывы:

ComAp InteliDrive DCU Marine, Руководство пользователя, Страница: 126 / 285

Результаты поиска

Содержание InteliDrive DCU Marine

Отзывы: