COMAC Vega 2019, Руководство по эксплуатации и обслуживанию

Страница: 14 / 40

HOW TO MOVE THE MACHINE
To transport the machine safely, proceed as follows:
1. Check to make sure that the solution tank and the recovery tank are empty. If this is not the case, empty them (see the sections titled
“ EMPTYING THE SOLUTION TANK ” and “ EMPTYING THE RECOVERY TANK ”).
2. Insert the key (4) into the main switch on the control panel. Set the main switch to "I" ( Fig.8 ).
3. Raise the brush head body and for versions without PM, depress the "BRUSH HEAD BODY CONTROL" pedal (1) at the rear of the machine
fully ( Fig.2 ). For versions with PM, lift the brush head body by pressing the “BRUSH HEAD CONTROL” button (6) on the control panel ( Fig.9 ).
4. Raise the squeegee body and turn the squeegee control lever (7) clockwise ( Fig.10 ).
5. When you push the dead man's lever (9) ( Fig.11 ), the machine will begin to move.
6. Use a ramp to move the machine up onto the transport vehicle.
CAUTION: During this operation, check there are no people or objects near the machine.
N.B.: the ramp gradient must not be such as to cause damage to the machine as it goes up.
7. Position the machine on the means of transport, and set the main switch to the “0” position by turning the key (4) a quarter turn anti-clockwise.
8. Grip the handle (5) on the left-hand side of the recovery tank ( Fig.7 ) and turn the tank as far as it will go.
9. Disconnect the electrical connector from the general system.
WARNING: This process must be carried out by qualified personnel.
10. Grip the handle (5) on the left-hand side of the recovery tank and turn the tank until it reaches the work position.
11. Fix the machine to the means of transport being used.
WARNING: secure the device according to the directives in force in the country of use, so that it cannot slide or tip over.
MACHINE SAFETY
To ensure that work is carried out in the best safety conditions, proceed as follows:
1. Make sure the solution tank is empty. If this is not the case, empty it (read " EMPTYING THE SOLUTION TANK ").
2. Make sure the recovery tank is empty. If this is not the case, empty it (read " EMPTYING THE RECOVERY TANK ").
3. Insert the key (4) into the main switch on the control panel. Set the main switch to "I" ( Fig.8 ).
4. Raise the brush head body and for versions without PM, depress the "BRUSH HEAD BODY CONTROL" pedal (1) at the rear of the machine
fully ( Fig.2 ). For versions with PM, lift the brush head body by pressing the “BRUSH HEAD CONTROL” button (6) on the control panel ( Fig.9 ).
N.B.: to lock the brush head in the raised position, depress the pedal (1) fully and then move it towards the right-hand side of the machine
( Fig.2 ).
5. Raise the squeegee body and turn the squeegee control lever (7) clockwise ( Fig.10 ).
6. Bring the main switch to position "0" by turning the key (4) a quarter turn anti-clockwise ( Fig.5 ). Remove the key from the instrument panel.
7. Grip the handle (5) on the left-hand side of the recovery tank ( Fig.7 ) and turn the tank as far as it will go.
8. Disconnect the electrical connector from the general system.
WARNING: This process must be carried out by qualified personnel.
9. Grip the handle (5) on the left-hand side of the recovery tank and turn the tank until it reaches the work position.
INSERTING THE BATTERIES IN THE MACHINE
To fit the batteries inside the machine, contact an COMAC assistance centre technician.
WARNING: COMAC declines all responsibility for any damage to property or injury persons in the event that the batteries are replaced by
an unauthorized technician.
TYPE OF BATTERY TO BE USED
Power to the machine must be supplied by four sealed traction batteries with gas recombination or gel technology. The batteries must meet the
requirements laid out in the norms: CEI EN 60254-1:2005-12 (CEI 21-5) + CEI EN 60254-2:2008-06 (CEI 21-7). In order to ensure good operating
performance, it is recommended to use four 6V MFP 180 Ah/C5 batteries.
14