manualshive.com logo in svg

COMAC ULTRA 85BS, Руководство по эксплуатации и техническому обслуживанию, Страница: 30 / 31

Поделиться
Скачать
COMAC ULTRA 85BS Скачать руководство пользователя страница 30

 

30

CHOOSING AND USING THE BRUSHES 

POLYPROPYLENE BRUSH (PPL) 

Used on all types of floors. Good resistance to wear and tear, and hot water (no greater than 60°C). The Polypropylene brush is 

non-hygroscopic and therefore retains its characteristics even when working in wet conditions. 

NYLON BRUSH 

Used on all types of floors. Excellent resistance to wear and tear, and hot water (even over 60°C). The nylon is hygroscopic and 

so tends to lose its characteristics over time when working in wet conditions. 

ABRASIVE BRUSH 

The bristles of this type of brush are charged with highly aggressive abrasives. It is used to clean very dirty floors. To avoid floor 

damage, work only with the pressure strictly necessary.  

THICKNESS OF THE BRISTLES 

Thicker bristles are more rigid and are therefore used on smooth floors or floors with small joints. 

On uneven floors or those with deep joints, it is advisable to use softer bristles which can enter the gaps more easily. 

Remember that when the bristles are worn and therefore too short, they will become rigid and are no longer able to penetrate 

and clean deep down. In this case, like with over-large bristles, the brush tends to jump. 

TABLE FOR CHOOSING THE BRUSHES

 

Machine

 

No. of 

brushes

 

Code

 

Type of bristles

 

Ø 

Bristles

Ø

Brush.

Notes

 

ULTRA 

85BS 

2 

404628 
404629 
404630 
404631 
404632 

PPL 
PPL 
PPL 
ABRASIVE  
MIXED ABRASIVE 

0.7 
0.8 
1.0 
1.0 

1.0+0.6 

210 
210 
210 
210 
210 

WHITE BRISTLES 
YELLOW BRISTLES 
BLACK BRISTLES 
GREY BRISTLES 
GREY BRISTLES 

Содержание ULTRA 85BS
































Отзывы:

Нет отзывов