COMAC ULTRA 85BS Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 31

COMAC ULTRA 85BS Скачать руководство пользователя страница 28

28

TROUBLESHOOTING

INSUFFICIENT WATER ON THE BRUSHES

1.  Check the tap is turned on
2.  Check the solenoid valve switch is on
3.  Check there is water in the solution tank (“RESERVE” indicator light off)

3

1

2

4. Clean the solution filter

THE MACHINE DOES NOT CLEAN WELL

1. Check the state of wear and tear of the brushes and, if necessary, replace them

(the brushes must be replaced when the bristles are about 15mm long).

2. Check the brush pressure is sufficient and, if necessary, increase it (see “BRUSH

PRESSURE” in the chapter “WORK”)

3. Use a different kind of brush to the one fitted as standard. For cleaning floors where

the dirt is particularly resistant, we recommend the use of special brushes supplied
upon request and according to needs (see “CHOOSING AND USING THE
BRUSHES”).

THE SQUEEGEE DOES NOT DRY PERFECTLY

1.  Check the squeegee is clean
2.  Adjust the height of the squeegee support (see “MACHINE PREPARATION”)
3.  Clean the entire suction unit (see “WEEKLY MAINTENANCE”)
4.  Replace the rubbers, if worn

«
...
26
27
28
29
30
...
»

Содержание ULTRA 85BS
































Отзывы:

Нет отзывов