COMAC ULTRA 85BS Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 31

COMAC ULTRA 85BS Скачать руководство пользователя страница 26

26

WEEKLY MAINTENANCE

CLEANING THE SUCTION TUBE

Whenever suction seems to be unsatisfactory, check that the suction tube
is not obstructed. If necessary, clean it with a water jet introduced from the
side where it is connected to the tank. Proceed as follows:
1. remove the suction tube from the curved sleeve of the recovery tank

(1)

2. disconnect the clamp (2) and remove the suction tube from the

squeegee suction sleeve

3. clean the inside of the tube with a jet of water
5. reassemble everything, carrying out the above-mentioned operations

in the reverse order

CLEANING THE SOLUTION TANK AND FILTER

With the solution tank empty:
1.  turn off the water tap
2.  unscrew the filter and rinse the inside thoroughly
3.  remove the cartridge and clean it
4.  reassemble everything, repeating the above-mentioned operations in

the reverse order

5. turn on the water tap

Note

: the filter can also be cleaned when the solution tank is full. Just

remember to turn off the tap

6. Loosen the upper cap
7. Rinse the tank with a water jet

1

2

«
...
24
25
26
27
28
...
»

Содержание ULTRA 85BS
































Отзывы:

Нет отзывов