COMAC ULTRA 85BS Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 31

COMAC ULTRA 85BS Скачать руководство пользователя страница 24

24

DAILY MAINTENANCE

CLEANING THE SQUEEGEE

1. Raise the squeegee by pressing the command lever forwards (1)

2.  Remove the suction tube from the squeegee sleeve (2)
3.  Remove the pins from the left and right squeegee bars (3)
4.  Loosen the small fixing columns (4)
5.  Rinse with running water and remove any impurities that may impede good

drying/suction

6. After cleaning, assemble the squeegee by carrying out the disassembly operations

in the reverse order

REPLACING THE SQUEEGEE RUBBER

If the squeegee rubber is worn and does not dry well, it is possible to change the drying
edge, proceeding as follows:
1.  push and rotate the fixing plates
2.  remove the rubber-pressing blade and the rubber itself
3.  turn the rubber upside-down and, if necessary, replace it
4. adjust the squeegee height as indicated in “ADJUSTING THE SQUEEGEE

SUPPORT HEIGHT” in the chapter “MACHINE PREPARATION”

Reassemble everything, carrying out the above-mentioned operations in the reverse
order

DISASSEMBLING THE BRUSHES

1.  Connect the battery connector if it is not already connected
2.  Turn the key to the ON position
3.  Use the lever to raise the base
Turn the key to the OFF position and remove it from the panel (carrying out the brush
disassembly operation with the power supply connected may cause injuries to the
hands)

1

2

«
...
22
23
24
25
26
...
»

Содержание ULTRA 85BS
































Отзывы:

Нет отзывов