COMAC ULTRA 85BS Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 31

COMAC ULTRA 85BS Скачать руководство пользователя страница 23

23

DAILY MAINTENANCE

CLEANING THE RECOVERY TANK

5. Empty the tank by means of the flexible tube, turning the knob a couple of times to

loosen it and then removing the cap (1)

6. To empty the tank quickly, loosen and remove the side plug (2)

This operation must be carried out using gloves to protect against
contact with dangerous solutions

1

2

7.

Open the hinge that fixes the tanks (3)

8.

Pull the tank slowly backwards until the blocking chain is taut (4)

3

4

9.

Open the hinge that fixes the suction cover (5)

10.

Open the cover by rotating it forwards until it is resting against the tank (6)

11.

Rinse the tank and clean the drainage tube

12.

Reposition the side plug and the plug on the exhaust pipe

13.

To close the suction cover and the tank, carry out the operations in the reverse
order

5

6

CLEANING THE SUCTION FILTER COVER

1.  Open the suction cover as indicated in the points above
2.  Remove the conical cover protecting the filter (1) by loosening the fixing screws (2)
3.  Remove the filter
4.  Wash it thoroughly then reposition it

1

2

«
...
21
22
23
24
25
...
»

Содержание ULTRA 85BS
































Отзывы:

Нет отзывов