COMAC ULTRA 85BS Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 31

COMAC ULTRA 85BS Скачать руководство пользователя страница 21

21

AT THE END OF THE WORK

At the end of the work, and before carrying out any type of maintenance, perform the
following operations:

1.  turn off the tap
2.  raise the base
3.  switch off the brush motor switch
4.  switch off the solenoid valve switch

5.  position the squeegee switch on manual mode
6.  raise the squeegee
7.  switch off the suction motor switch
8.  bring the machine to the place provided for draining the water
9.  make a 1/4 turn of the key, anticlockwise

10. Disconnect the exhaust pipe from its hook, unscrew the exhaust plug and empty

the recovery tank. To simplify the draining operation, you are advised to keep the
tube bent with one hand and, with the other, unscrew the knob and remove the
plug. Slowly straighten the tube and the liquid will start draining at the desired
speed.

This operation must be carried out using gloves to protect against
contact with dangerous solutions.

11. The squeegee must be raised when the machine is not operating, to avoid

deforming the rubber blades.

12. Disassemble the brushes and clean them with a jet of water (to disassemble the

brushes, see “DISASSEMBLING THE BRUSHES” below).

«
...
19
20
21
22
23
...
»

Содержание ULTRA 85BS
































Отзывы:

Нет отзывов