COMAC ULTRA 85BS Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 31

COMAC ULTRA 85BS Скачать руководство пользователя страница 14

14

MACHINE PREPARATION

8. SQUEEGEE

For packaging reasons, the squeegee may be supplied disassembled. It must be
assembled as shown in the figure, tightening the small columns (1) on the threaded
pins of the squeegee, in the special housings on the squeegee support

Insert the suction tube in the squeegee sleeve and fix it with the special clamp (2)

During working operation, the rear rubber is slightly tilted backwards (by about 5mm) in
a uniform way for its whole length.

If it is necessary to increase the bend of the rubber in the central part, you must tilt the
squeegee backwards, loosening the locknut (1) and rotating the tie-rod (2)
anticlockwise. To increase the bend of the rubber at the sides of the squeegee, loosen
the locknut (1) and rotate the tie-rod (2) clockwise. When fully adjusted, fix the locknut.

9. ADJUSTING THE SQUEEGEE HEIGHT

The height of the squeegee must be adjusted on the basis of the state of wear and
tear of the rubber. Proceed as follows:

1. loosen the ring nut (1)
2. use a CH17 spanner to turn the pivoting wheel, via the nut (2), clockwise to lift the

squeegee and anticlockwise to lower it

3. fix the ring nut (1)

NOTE:

the left and right pivoting wheels must be adjusted to the same height

1

2

1

2

1

2

«
...
12
13
14
15
16
...
»

Содержание ULTRA 85BS
































Отзывы:

Нет отзывов