COMAC ANTEA 50 B, Руководство по эксплуатации и обслуживанию

Страница: 35 / 44

12. Activate the brush head gearmotor using the brush control switch (7) ( Fig. 10 ).
13. When the dead man's lever (8) is engaged, the machine will start to move ( Fig. 11 ).
14. Activate the supply of detergent solution by pressing the switch (9) on the control panel ( Fig. 12 ).
15. Wait a few minutes, normally 2 – 4 minutes, to allow the dosing system to be washed.
N.B. : the machine will dispense solution during this operation.
16. After these 2 - 4 minutes have passed, empty the solution tank completely (read the paragraph titled
“ EMPTYING THE SOLUTION TANK ”).
8
7
9
11 10
12
CLEANING THE WATER SYSTEM (versions BT - BTS - BTO)
Prior to any extended periods of disuse, do the following:
1. Take the device to the dedicated maintenance area.
2. Take all necessary steps to ensure that the device is in a safe condition (see “ MACHINE SAFETY ”).
CAUTION Users are advised to always wear protective gloves, to avoid the risk of serious injury
to hands.
N.B.
: the place designated for this operation must comply with current environmental protection
regulations.
3. Make sure the recovery tank is empty, otherwise empty it completely (read the paragraph “ EMPTYING
THE RECOVERY TANK ”).
4. Verify that the quantity of detergent solution in the solution tank is suitable for the type of work you
wish to carry out, otherwise fill the solution tank (see the paragraph “ FILLING THE SOLUTION TANK
WITH WATER ”). View the level tube (1) in the rear of the machine ( Fig. 1 ).
5. Grip the handle (1) on the left side of the recovery tank ( Fig. 2 ) and turn the tank as far as it will go,
until it reaches the maintenance position ( Fig. 3 ).
6. Connect the battery connector (3) to the main system connector (2) ( Fig. 4 ).
ATTENTION: This process must be carried out by qualified personnel.
7. Grip the handle (2) on the side of the recovery tank ( Fig. 5 ).
8. Turn the recovery tank as far as it will go, to the work position ( Fig. 6 ).
9. Make sure the electronic brake is engaged. If it isn't, turn the lever (4) in the direction indicated by the
arrow. The traction gearmotor is located on the left side of the device ( Fig. 7 ).
10. Make sure the water tap is fully open: the water adjustment knob (5) should be completely down
( Fig. 8 ).
11. Turn on the appliance: bring the main switch (6) to its “I” position by turning the key (7) a quarter turn
to the right Fig. 9) ).
12. When the work screen appears on the control display, press the water flow adjustment button (8)
( Fig. 10 ).
N.B. : Set the amount of water present in the dosing system to maximum by pressing the button
(8) until the “WATER LEVEL ADJUSTMENT” symbol is completely filled ( Fig. 11 ).
1
1
3 2
2
4
3
2
2
6 5
7
4
8
5
7
6
9
13. Check that the potentiometer knob (9) is set to minimum. If it isn't, turn it completely counter-
clockwise ( Fig. 12 ).
N.B. : the device will not start to move (either forward or backward) if the potentiometer adjustment
knob (9) is set to minimum.
14. Lower the brush head unit by pressing the brush head control pedal (10) on the back of the appliance
(
Fig. 13
).
15. Lower the squeegee unit using the lever (11) on the back of the appliance ( Fig. 14 ).
16. When the dead man's lever (12) is activated ( Fig. 15 ), the brush head gearmotor and the vacuum
motor will enter into function. At the same time, the solenoid valve and dosing system will begin
supplying the detergent solution to the brush.
17. Wait a few minutes, normally 2 – 4 minutes, to allow the dosing system to be washed.
N.B. : the machine will dispense solution during this operation.
18. After these 2 - 4 minutes have passed, empty the solution tank completely (read the paragraph
“ EMPTYING THE SOLUTION TANK ”).
8
10
11
9
12
10
13
11
14
12
15
CLEANING THE WATER SYSTEM (versions BT - BTS - BTO with PM system)
Prior to any extended periods of disuse, do the following:
1. Take the device to the dedicated maintenance area.
2. Take all necessary steps to ensure that the device is in a safe condition (see “ MACHINE SAFETY ”).
CAUTION : users are advised to always wear protective gloves, to avoid the risk of serious injury
to hands.
N.B. : the place designated for this operation must comply with current environmental protection
regulations.
3. Make sure the recovery tank is empty, otherwise empty it completely (read the paragraph “ EMPTYING
THE RECOVERY TANK ”).
4. Verify that the quantity of detergent solution in the solution tank is suitable for the type of work you
wish to carry out, otherwise fill the solution tank (see the paragraph “ FILLING THE SOLUTION TANK
WITH WATER ”). View the level tube (1) in the rear of the machine ( Fig. 1 ).
5. Grip the handle (1) on the left side of the recovery tank ( Fig. 2 ) and turn the tank as far as it will go,
until it reaches the maintenance position ( Fig. 3 ).
6. Connect the battery connector (3) to the main system connector (2) (
Fig. 4
).
ATTENTION: This process must be carried out by qualified personnel.
7. Grip the handle (2) on the side of the recovery tank ( Fig. 5 ).
8. Turn the recovery tank as far as it will go, to the work position ( Fig. 6 ).
9. Make sure the electronic brake is engaged. If it isn't, turn the lever (4) in the direction indicated by the
arrow. The traction gearmotor is located on the left side of the device ( Fig. 7 ).
10. Make sure the water tap is fully open: the water adjustment knob (5) should be completely down
( Fig. 8 ).
1
1
3 2
2
4
3
2
2
6 5
35