The adjacent image identifies “EMERGENCY
SWITCH ACTIVE”.
The symbol in the middle of the screen indicates
that currently the emergency button has been
activated.
The adjacent image indicates “ELECTRONIC
BRAKE DISENGAGED”.
The symbol that appears in the middle of the
screen indicates that the appliance's electric
brake is not currently engaged.
The adjacent image shows the
“WORKING PANEL (CDS version)”
screen, with the following elements
identified:
1.
This icon shows the batteries'
charge level.
2. This icon shows the percentage of
chemical detergent present in the
detergent solution.
3. This icon shows the amount of
water present in the detergent
solution.
The adjacent image shows “WATER LEVEL
ADJUSTMENT” in the water circuit (versions
with CDS).
The symbol in the middle of the screen indicates
that the amount of water in the device water
circuit is being adjusted.
The adjacent image shows “WATER LEVEL AT
ZERO” in the water circuit (versions with CDS).
The symbol in the middle of the screen indicates
that the amount of water in the device water
circuit is currently at zero.
The adjacent image shows “DETERGENT
PERCENTAGE ADJUSTMENT” in the water
circuit (versions with CDS).
The symbol in the middle of the screen indicates
that the percentage of detergent in the device
water circuit is being adjusted.
The adjacent image shows “DETERGENT
PERCENTAGE AT ZERO” in the water circuit
(versions with CDS).
The symbol in the middle of the screen indicates
that the percentage of detergent in the device
water circuit is currently at zero.
The adjacent image shows the “SPRAY GUN
KIT ACTIVATION” only for SST versions.
The symbol in the middle of the screen indicates
that the spray gun kit is currently active.
3
2
1
PREPARING THE APPLIANCE
HANDLING THE PACKED APPLIANCE
Since the packaging elements (plastic bags, staples, etc.) are a potential source of danger, they should
not be left within the reach of children, disabled persons, etc.
Gross weight of device, including packaging, is:
•
95Kg for the Antea 50B
•
100Kg for the Antea 50BTS
•
105Kg for the Antea 50 BT-BTO
•
115Kg for the Versa 55-65 BT
•
000Kg for the Versa 60BTS
The packaging dimensions are:
•
A=610mm B=1250mm C=1135mm for Antea 50 B-BT-BTO
•
A=730mm B=1330mm C=1220mm for Antea 50BTS and Versa 55-65 BT
N.B.
: it is recommended that all the packaging components be kept
for any future transportation of the appliance.
DANGER
: move the packaged product with handling equipment
that complies with legal requirements regarding size and mass of
the packaging.
HOW TO UNPACK THE APPLIANCE (versions without PM)
The appliance is enclosed within special packaging; to remove the appliance from the packaging
proceed as follows:
1.
Place the lower part of the outer packaging in contact with the floor.
N.B.
: Use the pictograms printed on the box as reference.
2. Remove the outer package.
CAUTION
: these operations must be carried out using protective gloves to avoid any possible
contact with the edges or tips of metal objects.
3.
Raise the brush head unit and press the brush head control pedal (1) (on the rear of the device)
downwards (
Fig. 1
).
4.
Raise the squeegee unit and turn the squeegee control lever (2) in the direction of the arrow in
(
Fig. 2
). The lever is located on the back of the device.
5.
The device is fixed to the pallet by means of wedges (3) that block the wheels and brush head
(
Fig. 3
). Remove the wedges.
6.
For BT versions, release the electronic brake and turn the lever (4) in the direction of the arrow. The
traction gearmotor is located on the left side of the device (
Fig. 4
).
7.
Using a chute, bring the device down from the pallet, pushing it backwards.
N.B.
: Do not fit the brush and the rear squeegee unit before unloading the device, and avoid any
violent jolts to the brush head and the squeegee support.
N.B.
: during the operation to move it by pushing, the electric brake should not be engaged. The
device will anyway have safety braking, once a set critical speed has been exceeded the internal
braking system of the chopper circuit board will activate automatically.
1
2
2
1
3
3
4
4
HOW TO UNPACK THE APPLIANCE (versions with PM)
The appliance is enclosed within special packaging; to remove the appliance from the packaging
proceed as follows:
1.
Place the lower part of the outer packaging in contact with the floor.
N.B.
: Use the pictograms printed on the box as reference.
2. Remove the outer package.
CAUTION
: these operations must be carried out using protective gloves to avoid any possible
contact with the edges or tips of metal objects.
3.
Check that the appliance is off, if not, set the main switch (1) to “0”, turning the key (2) a quarter of a
turn to the left (
Fig. 1
). Remove the key from the instrument panel.
4.
Grip the handle (3) on the left side of the recovery tank (
Fig. 2
) and turn the tank as far as it will go in
the maintenance position (
Fig. 3
).
2
2
1
3
1
3
15
