UNITED KINGDOM
www.clasohlson.co.uk
Auto
Flash
C3
CS
IC Set
W/WW
Jump
C7
Meters
C16
7
6
10
8
9
4
5
3
2
1
Ver
. 20220613
LED Strip Light with Light Effects
Art.no 36-8068 Model SP-03LS3M-RGBPMD-01B
Read the entire instruction manual before use and save it for future reference.
We apologise for any text and picture errors and any changes of technical data.
If you have any questions concerning technical problems please contact our
Customer Services.
Safety
Warning:
• Neither the product nor its mains adapter may be dismantled or modified in any way.
• Never use the product or the mains adapter if it is in any way damaged or
malfunctioning. Unplug the product immediately if it is damaged.
• Do not use the product in explosive atmospheres or in the presence of
flammable liquids or gases.
• The product must only be connected to the included mains adapter.
• Never connect several or other types of devices to the mains adapter.
• The product must not be installed on a wet or electrically conductive surface.
• Make sure that the cables are not damaged whilst the product is being installed.
• Always unplug the mains adapter from the wall socket when the product is
not in use.
• Do not carry the product using the mains lead and do not use it for other
unsuitable purposes.
• Never let children play with the product.
• The product may be used by persons with reduced physical, sensory or
mental capabilities or persons with a lack of experience or knowledge which
could jeopardise their safety, provided they have been instructed in the safe
operation of the product and understand the hazards involved.
Important:
• The LEDs cannot be replaced. When the LEDs have reached the end of their
service life, the entire product must be discarded.
• This product is intended only for private use.
Risk of eye damage.
Do not look directly at the light source.
The product is not suitable for illuminating a room.
The product is intended for indoor use only.
Class II mains adapter.
Class III strip light
Installation
Information
The LED strip light can be mounted using the double-sided adhesive tape.
For best adhesion, ensure that the surface is clean, dry and free of grease.
If necessary, the length of the LED strip can be adjusted by cutting it at one of
the markings (every 10 cm along the length of the strip).
Note:
If the strip light is
shortened so that it has fewer than 48 LEDs remaining, the IC Set function will
not work.
1. Strip light: Remove the protective film from the tape on the back of the light
strip and attach it to a clean, grease-free surface. The strip light may also be
screwed on with plastic clips.
2. Connectors. Connect the strip light and the control box together.
Note:
Make sure the strip light is connected in the right way. Otherwise
the strip light will not shine.
3. IR Receiver.
Note:
Make sure there are no obstacles between the IR receiver
on the LED control unit and the remote control.
4. Connect the connecting cable to the LED control unit.
5. Plug the mains adapter into a suitable wall socket.
Remote control
Remove the plastic battery tab.
10. Select a specific direction for the different colours:
: The strip light shines fully and then gradually turns off the LED lights
from the middle of the strip and out to the sides.
: The LED lights turn on from the sides and move towards the middle.
: A group of 21 LED lights that move from one side to the other.
: 12 LED lights that move from one side to the other.
: The LED strip light lights up from one side to the other until
the whole strip light is lit. The lights go off and the next cycle starts.
: A group of 21 LED lights turn on and move from one side to
the other where the lights are gradually dimmed and then turn off.
Care and maintenance
• Unplug the mains lead from the wall socket before cleaning.
• The product should be cleaned using a dry cloth or vacuum cleaner.
Responsible disposal
This symbol indicates that the product should not be disposed of
with general household waste. This applies throughout the entire EU.
In order to prevent any harm to the environment or health hazards
caused by incorrect waste disposal, the product must be handed in
for recycling so that the material can be disposed of in a responsible
manner. When recycling your product, take it to your local collection
facility or contact the place of purchase. They will ensure that
the product is disposed of in an environmentally sound manner.
Specifications
Mains adapter
Power supply
230 V AC, 50 Hz
Output
12 V, 2 A DC
Light strip
Dimensions
3000 × 10 mm
Light source
90 × LED
Rated voltage
12 V DC
Rated power
19 W
Remote control
Range
Max 5 m
Battery
1 × CR2025 (included)
6. Choose between single or multiple colours:
CS:
1 colour
C3
: 3 colours (R,G, B)
C7
: 7 colours
C16
: 16 colours
7. Press [ IC Set ] and use [ ] and [ ] to
gradually turn off or turn on 6 LED lights at
a time (You can never have fewer than 48
active LEDs). Select a colour with the colour
selection buttons (6) and adjust the brightness
with [ ] and [ ].
8.
W / WW
: Change from warm white to cool white
: On/off
9. Auto: Switches between all colours and programmes
: A group of 15 LED lights in different colours moves from one side to
the other where the lights are gradually dimmed.
After a few cycles the direction changes and the LED lights move in the other direction.
Flash:
The whole strip light flashes. You decide if you want it to flash in
a single colour or multiple colours using the colour selection buttons (6).
Jump:
The whole strip light shines at the maximum brightness and changes
between on and off. If you have selected multiple colours, the strip light does
not turn off but switches between the selected colours.
Meteor:
A group of 21 LED lights turn on at the start and move from one
side to the other where the lights are gradually dimmed and then turn off.
21 LED lights turn on again and go in the opposite direction.
