UNITED KINGDOM • CUSTOMER SERVICE
tel. 020 8247 9300 e-mail [email protected] internet www.clasohlson.co.uk
postal Clas Ohlson Ltd, Aquilla House (First floor), 1 Becketts Wharf, Lower Teddington Road, Hampton Wick, Kingston Upon Thames, KT1 4ER
Auto
Flash
C3
CS
IC Set
W/WW
Jump
C7
Meters
C16
2
1
3
4
5
Ver
. 20200609
LED Strip Light with Light Effects
Art. no 36-8068
Model SP-02LS3M-RGBPMD-01B
Read the entire instruction manual before use and save it for future reference. We
apologise for any text and picture errors and any changes of technical data. If you have
any questions concerning technical problems please contact our Customer Services.
Safety
Warning:
• Neither the product nor its mains adapter may be dismantled or modified in any
way.
• Never use the product or the mains adapter if it is in any way damaged or
malfunctioning. Unplug the product immediately if it is damaged.
• Do not use the product in explosive atmospheres or in the presence of flammable
liquids or gases.
• The product must only be connected to the included mains adapter.
• Never connect several or other types of devices to the mains adapter.
• The product must not be installed on a wet or electrically conductive surface.
• Make sure that the cables are not damaged whilst the product is being installed.
• Always unplug the mains adapter from the wall socket when the product is not in
use.
• Do not carry the product using the mains lead and do not use it for other
unsuitable purposes.
• Never let children play with the product.
• The product may be used by persons with reduced physical, sensory or mental
capabilities or persons with a lack of experience or knowledge which could
jeopardise their safety, provided they have been instructed in the safe operation of
the product and understand the hazards involved.
Important
• The LEDs cannot be replaced. When the LEDs have reached the end of their
service life, the entire product must be discarded.
• This product is intended only for private use.
Remote control
Remove the plastic battery tab.
1. Choose between single or multiple colours:
CS:
1 colour
C3
: 3 colours (R,G, B)
C7
: 7 colours
C16
: 16 colours
2. Press [ IC Set ] and use [ ] and [ ] to
gradually turn off or turn on three LED lights at
a time. Select a colour with the colour selection
buttons (1) and adjust the brightness with [ ]
and [ ].
3.
W / WW
: Change from warm white to cool
white
: On/off
4. Auto: Switches between all colours and
programmes
: A group of 15 LED lights in different colours moves from one side to the other
where the lights are gradually dimmed.
After a few cycles the direction changes and the LED lights move in the other direction.
Flash:
The whole strip light flashes. You decide if you want it to flash in a single
colour or multiple colours using the colour selection buttons (1).
Jump:
The whole strip light shines at the maximum brightness and changes bet-
ween on and off. If you have selected multiple colours, the strip light does not turn
off but switches between the selected colours.
Meteor:
A group of 21 LED lights turn on at the start and move from one side to
the other where the lights are gradually dimmed and then turn off. 21 LED lights
turn on again and go in the opposite direction.
Risk of eye damage.
Do not look directly at the light source.
The product is not suitable for illuminating a room.
The product is intended for indoor use only.
Class II mains adapter.
Class III strip light
Installation
Information
The LED strip light can be mounted using the double-sided adhesive tape.
For best adhesion, ensure that the surface is clean, dry and free of grease.
If necessary, the length of the LED strip can be adjusted by cutting it at one of the
markings (every 10 cm along the length of the strip).
1. Strip light: Remove the protective film from the tape on the back of the light strip
and attach it to a clean, grease-free surface. The strip light may also be screwed
on with plastic clips.
2. Connectors. Connect the strip light and the control box together.
Note:
Make sure the strip light is connected in the right way. Otherwise the strip
light will not shine.
3. IR Receiver.
Note: Make sure there are no obstacles between the IR receiver on the LED
control unit and the remote control.
4. Connect the connecting cable to the LED control unit.
5. Plug the mains adapter into a suitable wall socket.
5. Select a specific direction for the different colours:
: The strip light shines fully and then gradually turns off the LED lights from
the middle of the strip and out to the sides.
: The LED lights turn on from the sides and move towards the middle.
: A group of 21 LED lights that move from one side to the other.
: 12 LED lights that move from one side to the other.
: The LED strip light lights up from one side to the other until the whole
strip light is lit. The lights go off and the next cycle starts.
: A group of 21 LED lights turn on and move from one side to the other
where the lights are gradually dimmed and then turn off.
Care and maintenance
• Unplug the mains lead from the wall socket before cleaning.
• The product should be cleaned using a dry cloth or vacuum cleaner.
Responsible disposal
This symbol indicates that the product should not be disposed of with
general household waste. This applies throughout the entire EU. In order
to prevent any harm to the environment or health hazards caused by
incorrect waste disposal, the product must be handed in for recycling
so that the material can be disposed of in a responsible manner. When
recycling your product, take it to your local collection facility or contact the
place of purchase. They will ensure that the product is disposed of in an
environmentally sound manner.
Specifications
Mains adapter
Power supply
230 V AC, 50 Hz
Output
12 V, 2 A DC
Light strip
Dimensions
3000 × 10 mm
Light source
90 x LED
Rated voltage
12 V DC
Rated power
24 W
Remote control
Range
Max 5 m
Battery
1 x CR2025 (included)
4
5
3
2
1