Colorjet VerveLED VLY 2513 Скачать руководство пользователя страница 7

Страница: 7 / 56

Page | 6

VERVE LED

Supporting Software Requirements

The

Supporting Software Requirements

are given as follow:

Table 2: Supporting Software Requirements

Requirements

Specifications

Printer Software

Provided by ColorJet

RIP Software

Provided by ColorJet

Tool Requirements

The

Tool Requirements

for printer installation are given as follow:

•

Magnifying lens (Carry by Engineer)

•

Multimeter (Carry by Engineer)

•

Wire Cutter

•

Nose plier

•

Screw driver set

•

Allen key set

•

Taper Gauge

•

Spanner

Environmental Requirements

The printer should be installed in a clean, dust-free environment, with temperature and relative
humidity range which are given as below:

•

Power ON

Temperature:

18 to 28

Humidity

: 20 to 60%RH (Non-condensing)

•

Power OFF

Temperature

: 5 to 40

Humidity

: 20 to 80%RH (Non-condensing)

Содержание VerveLED VLY 2513

























































Результаты поиска

Содержание VerveLED VLY 2513

Отзывы:

Похожие инструкции для VerveLED VLY 2513

Бренды по названию

Популярные бренды

Colorjet VerveLED VLY 2513, Инструкция по установке и устранению неисправностей

Результаты поиска

Содержание VerveLED VLY 2513

Отзывы:

Похожие инструкции для VerveLED VLY 2513

Бренды по названию

Популярные бренды