Colorjet VerveLED VLY 2513 Скачать руководство пользователя страница 48

Страница: 48 / 56

Page | 47

VERVE LED

Control System Maintenance

Follow the below given instructions for control system maintenance:

•

Static Discharge

One must discharge electrostatic waste of the machine before touch the electronic
components and parts of it.

Don

’

t touch the pin connectors and welded joints on circuit boards and integrated circuit

boards.

•

Control Wiring Maintenance

Check the control wiring of the machine whether loose or disconnected.

Check high-power output terminals whether loose or disconnected, such as the input and
output terminals of air switches, contactors, and relays.

Check the power system whether can provide the rated voltage to all parts of the machine
or not for smooth and stable operations.

Mechanical System Maintenance

Follow the below given instructions for maintenance of mechanical system of the machine:

•

Floor should be dust-free treatment before opening the machine.

•

Give lubrication oil to all the parts of the machine and the lubrication oil should with adhesion
force between 30cst to 150cst.

•

Carefully install the print heads. In case, print heads are not properly installed then it may cause
of head damage and bad printing results.

•

Check the tightness of carriage belt for quality printing.

•

Lubricate regularly to all parts of transmission bearings.

•

If the slider is not running smoothly, remove the same and clean it using the chemical provided
with the machine.

Encoder System Maintenance

Follow the below given instructions for maintenance of encoder scale:

•

Clean ink and dust from the Encoder ruler.

•

Check all the installation and connection screws carefully, if loose.

•

Clean the surface of Encoder Ruler and the direction Encoder for effective working.

•

Encoder sensors should be kept carefully. In case, Encoder ruler gets broken due to any reason,
then sensor is inactive or not working.

•

Keep water, ink, and oil away from the Encoder ruler to avoid Encoder ruler error.

•

Encoder sensor shouldn’t work in corrosion environment,

thus environmental condition should

be according to the environment condition.

Содержание VerveLED VLY 2513

























































Результаты поиска

Содержание VerveLED VLY 2513

Отзывы:

Похожие инструкции для VerveLED VLY 2513

Бренды по названию

Популярные бренды

Colorjet VerveLED VLY 2513, Инструкция по установке и устранению неисправностей

Результаты поиска

Содержание VerveLED VLY 2513

Отзывы:

Похожие инструкции для VerveLED VLY 2513

Бренды по названию

Популярные бренды