2
. Assemble six, steel, shock-corded, Leg Poles.
(Fig.
1)
3
. Push down on steel button on tapered end
and insert into end with four holes.
NOTE: Make sure steel button locks into
third hole on pole as shown. (Fig. 2)
4
. Assemble three, steel, shock-corded, curved
Ridge Poles. (Fig. 1)
5.
Stretch four corners of tent until taut; then
drive plastic stake web strap of each to
secure. (Fig. 3)
ROCKWALL
TM
12 TENT
MODEL 2000002596
STITCH LINE
To Set Up Tent
1.
Unfold tent and spread out on a clean, level surface with the door
facing the desired direction.
8.
Rotate all six Leg Poles upright and insert pin on each web
loop at the side locations as shown. (Fig. 7 & 7A)
(continued on other side)
Pole Descriptions
Pole
Pole Pole
Description
Qty.
Dia.
Repair Kit
Replacement Kit
Long Leg Pole, steel
(w/ red marking)
2
19mm
N/A
5010000678
Short Leg Pole, steel
4
19mm
N/A
5010000680
Curved Ridge Pole, steel
(w/ red marking)
1
19mm
N/A
5010000677
Curved Ridge Pole, steel
2
19mm
N/A
5010000679
Vertical Door Pole, black,
short w/rubber tips
1
6.3mm 5010000543
5010000545
Door Pole, black,
long w/rubber tips
1
6.3mm 5010000543
5010000545
Fig. 3
9.
Stretch tent to finished size:
• Push in button on Leg Pole while
twisting lower Leg Pole section
counterclockwise
(Fig.
8);
• Pull up on top Leg Pole section until
tent is taut;
• Twist the lower Leg Pole clockwise
until the button locks into the center
or lowest hole;
• Repeat on remaining Leg Poles.
10
. Locate Frame Clips on front and back of
tent; then attach to Leg Poles as shown.
(Fig.
9)
11
. Insert plastic stakes through
web straps located at bottom
of each Leg Poles; then drive
in to secure. (Fig. 10)
Fig. 8
Button
Center Hole
Lower Hole
Lower
Leg Pole
Section
Upper
Leg Pole
Section
Button in
third hole
Fig. 2
Curved Ridge Poles (3)
Leg Poles,
short (4)
Leg Poles,
long (2)
Fig. 1
6
. Insert Ridge Pole (with red marking) into center sleeve on top of tent
with the red trim (Fig. 4 & 6). Insert the remaining curved Ridge Poles
into the other two sleeves on top of tent.
7
. Insert curved end of Leg Pole (with red marking) into the ends of the
Ridge Pole (with red dot). Insert curved end of remaining short Leg
Poles into the ends of the remaining Ridge Poles. (Fig. 5 & 6)
Curved
Ridge Pole
with Red
Marking
Fig. 4
Sleeve
with Red
Trim
Ridge Pole with
Red Marking
Fig. 5
Sleeve
with Red
Trim
Curved End of
Long Leg Pole
Door
Curved Ridge Pole
in sleeve
Fig. 6
Long Leg Pole
Curved Ridge Pole in
sleeve with Red Marking
Short Leg Pole
Front of Tent
Short Leg Pole
Curved Ridge Pole
in sleeve
Fig. 10
Fig. 9
7A
Pin
Fig. 7
Hinged, Rigid Door
1.
Assemble Vertical Door Pole (shorter black pole with plastic tips);
then insert through zippered vertical pole sleeve on hinged side of
door. (Fig. 11)
2.
Insert end of Vertical Door Pole into bottom hinge plate, apply
pressure to form a slight bow, then insert other tip of pole into top
hinge. Zip up vertical pole sleeve. (Fig. 12 & 13)
3.
Assemble Door Pole (longer black pole with plastic cap tips); then
insert into zippered pole sleeve at top of door. (Fig. 14)
4.
Insert end of Door Pole into top hinge plate, apply pressure to form
a bow, then insert other tip of pole into the bottom hinge. (Fig. 15)
5.
Zip up pole sleeve to enclose Door Pole. (Fig. 16)
Fig. 11
Fig. 12
Fig. 13
Vertical Pole
Sleeve
Door Hinge
Fig. 14
Fig. 15
Fig. 16
Pole
Sleeve
Top
Door
Hinge
Pole
Sleeve
Top
Door
Hinge
Before you begin
Read all instructions before set up.
• Select a level site clear of rocks, branches, and other hard or sharp
objects, to install your tent.
WARNING: Keep clear of overhead power lines
.
• Do not set up your tent under trees because of potential lightning strikes
or falling tree limbs in inclement weather.
• Secure with
all
stakes and guylines provided to prevent property damage
or personal injury.
• For best results in windy conditions, position narrow end of tent into
the
wind.
• Enlist the help of at least one other person to assist you when it is time
to assemble the tent.
Self-Rolling Window Spring Descriptions
Color Code Description
Qty.
Length
Replacement Part No.
Green
1
610mm 5010000627
Orange
10
670mm 5010000628
CAUTION:
“Springs” may have sharp edges. Handle with care to avoid
injury.
Keep out of reach of children.
