Cognex In-Sight CIO-MICRO Скачать руководство пользователя страница 9

Страница: 9 / 65

Cables

Note

: Cables are sold separately.

CAUTION

All cable connectors are “keyed” to fit the connectors on the vision system; do not force the connections

or damage may occur.

Ethernet Cable

The Ethernet cable provides the Ethernet connection for network communications. When connected to the In-Sight Micro

vision system, this cable also supplies power to the vision system. This cable is available in the lengths and styles listed

below.

Length

Standard Part #

45-Degree Key Right-Angle

Part #

135-Degree Key Right-Angle

Part #

0.6 m

CCB-84901-1001-00

N/A

2 m

CCB-84901-1002-02

CCB-84901-6005-02

CCB-84901-7005-02

5 m

CCB-84901-1003-05

CCB-84901-6001-05

CCB-84901-7001-05

10 m

CCB-84901-1004-10

CCB-84901-6002-10

CCB-84901-7002-10

15 m

CCB-84901-1005-15

CCB-84901-6003-15

CCB-84901-7003-15

30 m

CCB-84901-1006-30

CCB-84901-6004-30

CCB-84901-7004-30

Introduction

Содержание In-Sight CIO-MICRO


































































Результаты поиска

Содержание In-Sight CIO-MICRO

Отзывы:

Похожие инструкции для In-Sight CIO-MICRO

Бренды по названию

Популярные бренды

Cognex In-Sight CIO-MICRO, Руководство по установке

Результаты поиска

Содержание In-Sight CIO-MICRO

Отзывы:

Похожие инструкции для In-Sight CIO-MICRO

Бренды по названию

Популярные бренды