Cognex DataMan 333L страница 59 Скачать руководство пользователя

Страница: 59 / 70

High-Speed Outputs

Specification

Description

Voltage

26.4V maximum through external load

Current

50mA maximum sink current

OFF state leakage current 100µA

External load resistance 240 Ohms to 10K Ohms

Each line rated at a maximum 50mA, protected against over-current, short circuits and transients from
switching inductive loads. High-current inductive loads require external protection diode.

The high-speed outputs can be used as either NPN (pull-down) or PNP (pull-up) lines. For NPN lines, the external load

should be connected between the output and the positive supply voltage (<26.4V). The outputs pull down to less than 3V

when ON, which causes current to flow through the load. When the outputs are OFF, no current flows through the load.

For PNP lines, the external load should be connected between the output and the negative supply voltage (0V). When

connected to a 24VDC power supply, the outputs pull up greater than 21V when ON, and current flows through the load.

When the outputs are OFF, no current flows through the load.

Connections, Optics, and Lighting

Содержание DataMan 333L






































































Результаты поиска

Содержание DataMan 333L

Отзывы:

Похожие инструкции для DataMan 333L

Бренды по названию

Популярные бренды

Cognex DataMan 333L, Справочное руководство

Результаты поиска

Содержание DataMan 333L

Отзывы:

Похожие инструкции для DataMan 333L

Бренды по названию

Популярные бренды