manualshive.com logo in svg

Coemar ISPOT 575 EB, Инструкция по эксплуатации, Страница: 25 / 26

Поделиться
Скачать
Coemar ISPOT 575 EB Скачать руководство пользователя страница 25

MBER

:

COMMUNICATION Error

This message indicates that the motherboard within the unit is not communicating properly with the con-
trol source. Check the connectors located on both boards.

OPER

:

PAN ENCODER Error

This message indicates that there is a problem with the PAN encoders. Check the sensors on the encoder
wheel located near the pan movement motor, as well as the relevant cabling.

OTER

:

TILT ENCODER Error

This message indicates that there is a problem with the TILT encoder locate on the fixture yoke. Check the
sensors on the encoder wheel located near the pan movement motor, as well as the relevant cabling.

LAER

:

LAMP Error

The lamp has turned off unexpectedly, without any signal from the controller to do so. The system may
have exceeded the allowable number of attempts to ignite the lamp (10) after which number the system
is designed to protect ignitor, cabling and the lampholder by reducing the incidence of lamp ignition vol-
tages to these components. Check and eventually replace the lamp if it is faulty, damaged, or has excee-
ded its lamp life.

EPER

:

EEPROM Error

The EEPROM is either defective or absent; refer to your coemar service centre for a replacement compo-
nent.

DTER

:

DATA Error

The initial parameter settings are incorrect or corrupt; the projector has reloaded its factory default settings.
Turn the projector off and on again. Should the error reoccur, refer the unit to your authorised coemar ser-
vice centre to have the EEPROM check and possibly replaced.

ADER

:

DMX addressing Error

The projector is not receiving all DMX channels needed to operate correctly. Check the DMX address indi-
cated on the display and the channel numbers being outputted from the controller. Note that not all con-
trollers will output all 512 channels.

S1ER

:

Control Circuit Error relating to position sensors for the 5 motor PCB. Sensor not
reading the magnet.

Check for the presence of power to the PCB and the condition of the connectors and cabling between the
PCB and the sensors. Additionally, check motors and/or cogs for any impediments as well as the proper
position of the cabling connectors.

S2ER

:

Control Circuit Error relating to position sensors for 4 motor PCB (located in the yoke at 
right when viewed from the rear of the unit). Sensor not reading the magnet.

Check for the presence of power to the PCB and the condition of the connectors and cabling between the
PCB and the sensors. Additionally, check motors and/or cogs for any impediments as well as the proper 
position of the cabling connectors.

S3ER

:

Control Circuit Error relating to position sensors for 4 motor PCB (located in the yoke at 
left when viewed from the rear of the unit). Sensor not reading the magnet.

Check for the presence of power to the PCB and the condition of the connectors and cabling between the
PCB and the sensors. Additionally, check motors and/or cogs for any impediments as well as the proper
position of the cabling connectors.

C1ER

:

Position Error in colour wheel number 1 (closest to lamp). Sensor not reading the magnet. 

Check for correct functioning of the motor and the magnetic sensor and the correct positioning with
respect to the sensor and encoder wheel..

C2ER

:

Position Error in colour wheel number 2. Sensor not reading the magnet. 

Check for correct functioning of the motor and the magnetic sensor and the correct positioning with
respect to the sensor and encoder wheel..

G1ER

:

Position Error in gobo wheel number 1 (closest to lamp). Sensor not reading the magnet.

Check for correct functioning of the motor and the magnetic sensor and the correct positioning with
respect to the sensor and encoder wheel..

G2ER

:

Position Error in gobo wheel number 2. Sensor not reading the magnet. 

Check for correct functioning of the motor and the magnetic sensor and the correct positioning with
respect to the sensor and encoder wheel..

R1ER

:

Position Error in gobo indexing on wheel 1. (closest to lamp). Sensor not reading the magnet.

Check for correct functioning of the motor and the magnetic sensor and the correct positioning with
respect to the sensor and encoder wheel..

R2ER

:

Position Error in gobo indexing on wheel 2. Sensor not reading the magnet. 

Check for correct functioning of the motor and the magnetic sensor and the correct positioning with
respect to the sensor and encoder wheel..

24. Error messages

English 

Содержание ISPOT 575 EB



























Отзывы:

Нет отзывов