CODEL EnergyTech 301 Скачать руководство пользователя страница 12

Страница: 12 / 49

CODEL

Page 4

Operation and Maintenance

Issue: A

Revision: 4

Date: 03/11/20

Ref:100255

1.3.1

Main Menu

The Instrument has following main menus.

➔

Measurements

➔

Diagnostics

➔

Setup Mode

1.4

Measurements

This initial and default screen displays the measurement reading of the device. An overview of Measurements sub-
menus is shown below.

Press

to exit to main screen and press

, the following screen appears.

1.4.1

Select Channel

Allows user to select measurement based on units. The following are the submenus.

Unit: %

Displays dust levels in percentage.

Use

to scroll through to % and press

to select %. The display returns to measurement screen

displaying % measurement.

Main Menu

Sum menu 1

Sub menu 2

Measurements

Select Channel %

Select Channel mg/m3

Select Channel mg/Nm3

Select Channel All Channels

Exit

Содержание EnergyTech 301


















































Результаты поиска

Содержание EnergyTech 301

Отзывы:

Бренды по названию

Популярные бренды

CODEL EnergyTech 301, Инструкция по интерфейсу

Результаты поиска

Содержание EnergyTech 301

Отзывы:

Бренды по названию

Популярные бренды