background image

10

2009 Audiovox Electronics Corporation. All rights reserved.

     4

BLACK/YELLOW

PULSE DURING CRANK ( - )

Locate the vehicle’s second starter (crank) wire at the ignition switch. (if equipped)

Verification: This wire registers voltage only in the start (crank) position of
the ignition switch.

Connect the BLACK/YELLOW wire as shown in the diagram below.  Use an SPDT
relay (not supplied).

F us ed +12 Volt
B attery S ource

30

87

87a

86

85

B L AC K /Y E L L OW   P uls e
During C rank W ire

To Vehicle's 2nd 
   S tarter W ire

   J ump To P UR P L E
     S tarter O utput 
     W ire F rom T he
    C ontrol Module

2 Pin  Lock Output Harness

1

BLUE

UNLOCK ( - )

The door unlock output wire provides an output only while the remote start feature
is active.

3

GREEN/WHITE

FACTORY ARM /

PULSE AFTER SHUTDOWN  ( - )

This wire will supply a ( - ) 500mA pulse both upon arming the system and after
the remote start shuts down. This is typically used to re-lock the vehicle’s doors if
they unlock upon remote start shutdown.  It can also be used to pulse a door pin-
switch wire to prevent the vehicle’s accessories from remaining on after remote
start shutdown.

Содержание Professional Series CA 4050





















Отзывы: