Cobalt Digital Inc BBG-1034-AUD-PRO Скачать руководство пользователя страница 80 | Manualshive

Страница: 80 / 114

Cobalt Digital Inc BBG-1034-AUD-PRO Скачать руководство пользователя страница 80

3

BBG-1034-AUD-PRO Function Menu List and Descriptions

3-48

BBG-1034-AUD-PRO PRODUCT MANUAL

BBG-1034-AUDPRO-OM (V1.1)

Reticules

Allows Safe Action and/or Safe Title overlays and other
static markers to be added to the output video image.

Note: • Overlay markers using this function are for setup only. When enabled, these markers are embedded in the output

video and will appear in the image. Use this function only on preview video and not on-air video. Make certain any
overlay tools are turned off when no longer needed.

• Multiple overlay markers described below can be simultaneously enabled as desired.

• Insertion Master Enable/Disable

Provides independent master enable/disable for SDI and CVBS outputs.

• When enabled, any combination of reticules or other markers described

below can be inserted.

• When disabled, insertion of all reticules or other markers is disabled.

• Safe Action Area (SAA) Controls

• SAA provides enable/disable of safe action area graticule insertion.

• SAA Height and SAA Width control height and width of insertion (from

0% to 100% of 4:3 outputted image area).

Note: Reticule Size control is locked to Custom for this device, with safe

action area size control as described above.

Table 3-1

BBG-1034-AUD-PRO Function Menu List — continued

Typical Reticule/Overlay Marker Insertions

The BBG-1034-AUD-PRO allows any combination of the reticule/overlay markers to be applied to the output video. Sizing and
other characteristics for each type of marker can be set as described below.

Safe Action Area (SAA) Reticule

Safe Title Area (STA) Reticule

Graticule

Center Cross

«
...
78
79
80
81
82
...
»

Содержание BBG-1034-AUD-PRO



















































































































Отзывы:

Нет отзывов