background image

EN

G

LI

S

H

Kickback and Related Warnings

Kickback is a sudden reaction to a pinched or snagged rotating wheel, backing 
pad, brush or any other accessory. Pinching or snagging causes rapid stalling of 
the rotating accessory which in turn causes the uncontrolled power tool to be for-
ced in the direction opposite of the accessory’s rotation at the point of the binding.

For example, if an abrasive wheel is snagged or pinched by the workpiece, the 
edge of the wheel that is entering into the pinch point can dig into the surface 
of the material causing the wheel to climb out or kick out. The wheel may either 
jump toward or away from the operator, depending on direction of the wheel’s 
movement at the point of pinching. Abrasive wheels may also break under these 
conditions.

Kickback is the result of power tool misuse and/or incorrect operating procedures 
or conditions and can be avoided by taking proper precautions as given below.

a)   Maintain a firm grip on the power tool and position your body and arm to allow 

you to resist kickback forces. Always use the auxiliary handle, if provided, 
for maximum control over kickback or torque reaction during start-up. The 
operator can control torque reactions or kickback forces, if proper precautions 
are taken.

b)   Never place your hand near the rotating accessory. Accessory may kickback 

over your hand.

c)   Do not position your body in the area where power tool will move if kickback 

occurs. Kickback will propel the tool in direction opposite to the wheel’s 
movement at the point of snagging.

d)   Use special care when working corners, sharp edges etc. Avoid bouncing and 

snagging the accessory. Corners, sharp edges or bouncing have a tendency to 
snag the rotating accessory and cause loss of control or kickback.

e)   Do not attach a saw chain woodcarving blade or toothed saw blade.  

Such blades create frequent kickback and loss of control.

Product marking with safety symbols

 

 

 

 

Read the entire instruction manual!

 

 

 

 

 

Always use ear protection and protective goggles or a visor. 

Содержание S1J-AJ8-10

























Отзывы:

Похожие инструкции для S1J-AJ8-10