Cmsemicon CMS80F731 Series Скачать руководство пользователя страница 213

Страница: 213 / 239

www

.mcu.com.cn

214

239

Rev.

1.00

CMS80F731x Reference Manual

23.6 Related Registers

There are 11 main registers associated with AD conversion, namely:

⚫

AD control registers ADCON0, ADCON1, ADCON2, ADCCHS, ADCLDO;

⚫

Comparator control register ADCPC;

⚫

Delay data register ADDLYL;

⚫

AD result data register ADRSH/L;

⚫

Comparator data register ADCCMPH/L.

23.6.1

AD Control Register ADCON0

0xDF

Bit7

Bit6

Bit5

Bit4

Bit3

Bit2

Bit1

Bit0

ADCON0

ADFM

ANACH3

ANACH2

ANACH1

ANACH0

ADGO

R/W

Reset value

Bit7

Reserved, must be 0.

Bit6

ADFM:

ADC conversion result format select bits;

Right alignment;

Left-aligned.

Bit5~Bit2

ANACH<3:0>:

ADC channel 63 input source select bit;

0000=

BGR(1.2V);

0001=

Reserved, prohibited use;

0010=

Reserved, prohibited use;

0011=

Reserved, prohibited use;

0100=

Reserved, prohibited use;

0101=

VSS (ADC Reference Area);

0110=

Reserved, prohibited use;

0111=

VDD (ADC default reference voltage).

Other =

Reserved, prohibited.

Bit1

ADGO:

ADC converts the start bit (ADEN must be 1 for this bit set to 1, otherwise the

operation is invalid);

Write: Starts the ADC conversion, (the hardware also uses this bit set to 1 when the

ADC is triggered);

Read: The ADC is converting.

Write: Invalid.

Read: ADC idle/converted;

During the conversion of the ADC (ADGO=1), any software and hardware trigger

signals are ignored.

Bit0

Reserved, must be 0.

Содержание CMS80F731 Series
















































































































































































































































Результаты поиска

Содержание CMS80F731 Series

Отзывы:

Бренды по названию

Популярные бренды

Cmsemicon CMS80F731 Series, Справочное руководство

Результаты поиска

Содержание CMS80F731 Series

Отзывы:

Бренды по названию

Популярные бренды