Cmsemicon BAT32G1 9 Series Скачать руководство пользователя | Manualshive

Страница: 1148 / 1149

background image

BAT32G1x9 user manual | Chapter 35 FLASH control

1148 / 1149

Rev.1.02

35.4.2

Chip erase

chip erase, the erase time is implemented by hardware and can also be configured via FLCERCNT. The

operation process is as follows:

1)

Set up FLERMD. ERMD0 is 1'b 1, select chip erase mode;

2)

Set FLPROT to 0xF1 to de-protect FLOPMD. Then set FLOPMD1 to 0x55 and FLOPMD2 to 0xAA

3)

Write arbitrary data to any address in the flash area of the code.

4)

Software query status register FLSTS. OVF, when OVF=1, indicates that the erase operation is
complete.

5)

Before proceeding to the next operation, the software sets "1" to clear FLSTS.

35.4.3

Word program

word programming, write time is implemented by hardware and can also be configured via PROCNT. The

operation process is as follows:

1)

Set FLPROT to 0xF1 to de-protect FLOPMD. Then set FLOPMD1 to 0xAA and FLOPMD2 to 0x55

2)

Writes the appropriate data to the destination address.

3)

Software query status register FLSTS. OVF, when OVF=1, indicates that the write operation is
complete.

4)

Before proceeding to the next operation, the software sets "1" to clear FLSTS.

35.5 Flash read

The fastest finger frequency supported by flash built into this device is 32 MHz. When the HCLK

frequency exceeds 32MHz, the hardware inserts a 1 wait period when the CPU accesses flash.

35.6 Considerations for FLASH operations

⚫

Flash memory has strict time requirements for the control signal of erasing and programming operation,
and the timing of the control signal is not qualified, which will cause the erase operation and
programming operation to fail. The setting of the erase and write parameters can be implemented by
hardware, or it can be modified by modifying the parameter registers; When using internal high-speed
OCO, MAINOSC/ external input clock = 20M, it is recommended to use hardware-set erase and write
parameters without setting parameter registers.

⚫

If the wipe and write operation is performed from within FLASH, the CPU stops taking the finger and
the hardware automatically waits for the operation to complete before proceeding to the next
instruction. If the operation is performed from the RAM, the CPU does not stop taking the finger and
can now proceed to the next instruction.

⚫

While FLASH is in programming, if the CPU executes the instruction to enter a deep sleep, the system
will wait for the programming action to end before entering a deep sleep.

«
...
1146
1147
1148
1149
»

Содержание BAT32G1 9 Series






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BAT32G1 9 Series

Бренд: Badger Meter Страницы: 20

Бренд: OES Страницы: 3

Бренд: Parkside Страницы: 86

Бренд: Parkside Страницы: 65

Extra Free RZB-02

Бренд: Zamel Страницы: 2

Бренд: HEIDENHAIN Страницы: 257

Бренд: Olsen Страницы: 4

Бренд: ADLINK Technology Страницы: 37

Бренд: SSHC Страницы: 2

Бренд: OK-I Страницы: 10

Бренд: Danfoss Страницы: 8

Бренд: Warner Electric Страницы: 4

Бренд: Salus Страницы: 40

Бренд: Jabra Страницы: 13

Бренд: Vector Страницы: 649

Smatrix Wave PLUS

Бренд: Uponor Страницы: 4

Бренд: Yamatake Страницы: 156

Бренд: MEI Страницы: 199

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды