CML Microcircuits PE0601 Series Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 34

CML Microcircuits PE0601 Series Скачать руководство пользователя страница 6

Evaluation Kit for CMX7x6x

PE0601-xxxx

©

2011 CML Microsystems Plc

6

UM0601/2

2

Preliminary Information

The PE0601-xxxx is designed to support the CMX7x6x range of

FirmASIC

®

devices using their

respective Function Image

TM

.

The PE0601-xxxx is supplied with a customer specified target device fitted where xxxx in the
product code is the numerical part of the target device product code.

For example:

To evaluate a CMX7163 Function Image

TM

(FI), order a PE0601-7163.

In this document the PE0601-xxxx will be referred to generically as PE0601.

Note that the Function Image

TM

will redefine many pin functions and so the pins may be labelled

differently, as a result. The pin numbers will remain unchanged. The datasheet and user manual
appropriate to the product code and Function Image

TM

should be used as the definitive reference

of functionality, rather than this PE0601 document, which only uses generic pin names.

2.1

Laboratory Equipment

The following laboratory equipment is needed to use this evaluation kit:

A 5 volt dc regulated power supply or +/- 5 volt if the instrumentation interface is required.

If the PE0601 is being used with the PE0002 Interface Card, the following items will also be
required:
1. An IBM compatible PC with the following requirements:

•

One of the following Windows operating systems installed: 2000sp4 or XPsp2

•

USB port

•

Minimum screen resolution 800 x 600. Recommended resolution 1024 x 768.

2. A USB type A male to mini B male cable.

3. Software

application

ES000230.exe

, or later version, installed on the PC.

2.2

Handling Precautions

Like most evaluation kits, this product is designed for use in office and laboratory environments.
The following practices will help ensure its proper operation.

2.2.1 Static Protection

This product uses low power CMOS circuits that can be damaged by electrostatic discharge.
Partially damaged circuits can function erroneously, leading to misleading results. Observe ESD
precautions at all times when handling this product.

2.2.2 Contents - Unpacking

Please ensure that you have received all of the items on the separate information sheet (EK0601)
and notify CML within 7 working days if the delivery is incomplete.

2.3

Approvals

This product is not approved to any EMC or other regulatory standard. Users are advised
to observe local statutory requirements, which may apply to this product.

«
...
4
5
6
7
8
...
»

Содержание PE0601 Series



































Отзывы:

Нет отзывов