3
P/N 192044557 REV AA
September 2017
STEP 4:
Change the adjustment of the load limiter by tightening the
groove nut with the spanner socket tool to increase the setting or by
loosening the groove nut to decrease the setting. See Table 1.
Capacity
Setting
lbf-ft
¾ tonne
55-60 Nm
40.5-44.2
1 ½ tonne
95-100 Nm
70-73.7
3 tonne
95-100 Nm
70-73.7
6 tonne
100-105 Nm
73.7-77.4
Table 1: Torque Setting
When setting load limiter, turn clockwise to increase setting, counter-
clockwise to decrease setting. If decreased setting is required,
loosen adjusting ring and then tighten to desired setting. Revise the
adjustment if necessary.
NOTE:
The hoist should not be able to lift
160% of the rated capacity load if the load limiter has been properly
adjusted.
STEP 5:
Replace the center cap and the three screws in the
handwheel cover.
DISASSEMBLY AND ASSEMBLY
When disassembling and re-assembling the units, please refer to
the maintenance section of the CM Hurricane 360 O&M Manual (P/N
656) and this supplement so that all parts are properly installed.
Prior to re-assembly, check all parts for excessive wear, cracks and
distortion. Replace parts as necessary, and then reassemble the unit
according to the CM Hurricane 360 O&M Manual (P/N 656) and this
supplement.
TESTING
We recommended to test the load limiter after adjustment.
Wear and use proper safety equipment for testing. Follow all safety
instructions and warnings in this supplement and in the operation
manual for inspecting, maintaining and operating this hoist.
The use of any hoist presents some risk of personal injury or
property damage. That risk is greatly increased if proper instructions
and warnings are not followed. Before using this hoist, each operator
should become thoroughly familiar with all warnings, instructions
and recommendations in this manual. Retain this manual for future
reference and use.
To perform this test, attach the lower hook to a load of maximum
160% of rated capacity and operate the unit in the “up” direction.
When attempting to lift the load, the lever should slip. After this
test, move the trigger to the down position and operate the unit to
remove the tension from the units. Once tension is released, the unit
should return to normal operation. If the load does not slip @ 160%
of capacity, the load limiter needs to be replaced.
Any hoists that have been repaired or not been operated for the
previous 12 months, shall be tested by the user for proper operation
prior to initial use.
See the CM Hurricane 360 O&M Manual (P/N 656) for more
information.
Questions regarding the Load Limiter on your CM Hurricane 360
Chain hoist should be directed to Columbus McKinnon technical
support.
Columbus McKinnon
Industrial Products GmbH
Yale-Allee 30
42329 Wuppertal / Germany
Modeled:
Drawn:
Approved:
Design Authority:
Original project:
Original scale:
1:2
Material:
General Tolerances
ISO 2768-mk
Dimensional Units
mm
Description:
Number:
Sheet
1
1
Format
F
E
D
C
B
A
1
2
3
4
A4
Columbus McKinnon
Industrial Products GmbH
Wuppertal / Germany
Columbus McKinnon Industrial Products GmbH claims proprietary r
ights in the material disclosed hereon. This drawing and/or tec
hnical information is issued in confidence
for engineering information only and may not be reproduced or u
sed to manufacture anything shown or referred to hereon without
direct permission
from Yale to the user. This drawing and/or technical informatio
n is loaned for mutual assistance and is subject to recall by Y
ale at any time.
This drawing and/or technical information is the property of Ya
le.
NOTICE TO PERSONS RECEIVING THIS DRAWING AND/OR TECHNICAL INFOR
MATION
ECN
Rev. Description of change
Date
By
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
04/08/2008
04/08/2008
Velbert
kon3
kon3
Hurricane III 1,0/1
Hand chain hoist 1000/1
Flaschenzug 1000/1 - VG
84700017
kon6
04/14/2010
Standard:
Material No:
Specified Tolerances
ISO 8015
Edges According to
DIN 6784
First Angle Projection
