manualshive.com logo in svg

Club Car Carryall 1, Дополнение к руководству по обслуживанию и ремонту, Страница: 62 / 176

Поделиться
Скачать
Club Car Carryall 1 Скачать руководство пользователя страница 62

IQ DISPLAY MODULE (IQDM) SERIES 2 AND IQDM-P DIAGNOSTICS

Monitor Menu

Page 12-4

2008-2011 IQ System Electric Vehicle Maintenance and Service Supplement

12

Information

The 

information

 menu displays the model number, serial number, manufacturer date and software version of

the speed controller. 

See Information, Section 12, Page 12-14.

Programmer Setup

The 

programmer setup

 menu allows the user to set the LCD contrast, display the fault history of the program-

mer as well as various other information pertaining to the handset such as model number, serial number,
OEM information, etc. 

See Programmer Setup, Section 12, Page 12-14.

MONITOR MENU

The 

monitor

 menu is accessed by using the up or down arrow to scroll to 

monitor

 and pressing the right arrow

key to activate the menu. All information in the 

monitor

 menu is updated in real time, allowing the trained tech-

nician to troubleshoot the vehicle by monitoring the handset as the key switch is cycled, Forward/Reverse
switch is activated, etc.

Since the 

monitor

 menu is updated while the vehicle is in operation, the trained technician has the ability to

monitor the status of several components in conditions or locations where a problem with vehicle performance
has been reported. 

See following WARNING.

ý 

WARNING

• The vehicle operator should not monitor the handset while the vehicle is in motion. A

technician can monitor the handset while traveling as a passenger in the vehicle. Failure to
heed this warning could result in severe personal injury or death.

The following parameters can be monitored in real time with the handset from the 

monitor

 menu:

Throttle

Indicates the position of the accelerator pedal from 0% (pedal not pressed) to 95 - 100% (pedal fully pressed).
This item can be monitored when the key switch is in the ON or OFF position.

Batt Voltage

Displays the current battery voltage at the speed controller.

Heatsink

Displays the temperature (in degrees Celsius) of the speed controller heatsink. During normal operating con-
ditions, the heatsink temperature should be below 85 °C ±5 °C (185 °F ±9 °F). 

See following NOTE.

NOTE: 

Improper brake adjustment can sometimes cause the operating current to be higher than normal.
This higher current increases the temperature of the speed controller heatsink.

Arm Current

Displays the motor armature current (in amperes).

Field Current

Displays the motor field current (in amperes).

Содержание Carryall 1

















































































































































































Отзывы:

Нет отзывов