3
<NOTE>
&
If the remote keypad did not sound a long beep, it means the remote keypad did not send the learning
code to the Control Panel, please press
＊
key then
7
key again to send the learning code..
III. If the Control Panel receives the learning code, it will display the info accordingly. Refer to the operation
manual of your Control Panel to complete the learn-in process.
IV. After Control Panel receives the signal from remote keypad, it will send an acknowledgement back to remote
keypad. The remote keypad will then beep 3 times to confirm the acknowledgement has been received.
Dual-Key Learning:
I. Press
and
both
#
and
＊
keys together under Normal Operation Mode. Remote Keypad will sound a long
beep.
<NOTE>
&
If the remote keypad did not sound a long beep, it means the remote keypad did not send the learning
code to the Control Panel, please press both
#
and
＊
keys together again to send the learning code.
II. If the Control Panel receives the learning code, it will display the info accordingly. Refer to the operation
manual of your Control Panel to complete the learn-in process.
III. After Control Panel receives the signal from remote keypad, it will send an acknowledgement back to remote
keypad. The remote keypad will then beep 3 times to confirm the acknowledgement has been received.
<IMPORTANT NOTE>
&
If remote keypad does not perform 3 beeps, please restart the learning procdeure.
Step 3.
After the Remote keypad is learnt-in, put the Control Panel into
Walk Test
mode, hold the Remote keypad in the
desired location, and send the learning code to the Control Panel to confirm this location is within the signal range
of the Control Panel. To send the learning code, either press the
＊
key then
7
key under Test Mode or press
both
#
and
＊
keys together under Normal Operation Mode.
Step 4.
When you are satisfied that the Remote keypad works in the chosen location, you can proceed with mounting the
Remote keypad following the steps described below (see
Mounting Remote keypad)
.
Step 5.
Set your own the KP Pin Code:
I.
When the keypad is under Test mode, press
＊
key then
6
key, a long beep will be sound.
II. Enter
0000
(default PIN code)
III. Press
Χ
key, remote keypad sounds a long beep.
IV. Enter your new 4-digit code.
V. Press
#
key, remote keypad sounds a long beep. The new PIN code is enabled.
Step 6.
Press
key
twice
to leave Test mode and the installation is completed.
z
Mounting Remote Keypad
I.
Remove the front cover.
II. Using the 2 mounting holes of the back cover as a template, mark off the positions in the most appropriate place.
III. Insert the wall plugs if fixing into plaster or brick surface.
IV. Screw the Remote keypad onto the wall plugs.
V. Replace the front cover.
z
How to Set System Mode
You may choose to arm/home arm with/without Control Panel User PIN Code.
Arm/Home with Pin Code
Under Test mode, Pressing
＊
key and then
9
key to enable Arm/ Home with PIN Code function (
Default
).
¾
Enter Arm Mode
: Enter any one of Control Panel user code and press
key. If panel has no fault and arming is
successful, the Status Red LED will turn ON alone with a long beep.
¾
Enter Home Mode
: Enter any one of Control Panel user cods and
key. If panel has no fault and arming is
successful, the Status Red LED will flash 4 times alone with 3 beeps.
¾
Return to Disarm Mode
: Enter any one of Control Panel user code and
key. If disarm is successful, the
Status Blue LED will turn ON along with 2 beeps.
Arm/Home without PIN Code
In the Test mode, Pressing
＊
key and then
8
key to enable Arm/ Home without PIN Code function
¾
Enter Arm Mode
: Press
key. If panel has no fault and arming is successful, the Status Red LED will turn ON
alone with one long beep.
¾
Enter Home Mode
: Press
key. If panel has no fault and arming is successful, the Status Red LED will flash 4
times alone with 3 beeps.
¾
Return to Disarm Mode
: Enter any one of Control Panel user code and
Key. If disarm is successful, the
Status Blue LED will turn ON along with 2 beeps.
