Climax H&S TOOL SPEED FACER ODF100 Скачать руководство пользователя страница 64

Страница: 64 / 132

Page 46

ODF Speed Facer Operating Manual

CAUTION

Avoid damage, premature machine wear, and
protect your warranty by using only approved
lubricants.

5.3

AINTENANCE

TASKS

Maintenance tasks are described in the following sec-
tions.

5.3.1

Checking the Air Caddy oil reser-
voir and particulate filter trap

Do the following to check the Air Caddy oil reservoir and
particulate filter trap:

1. Check the Air Caddy oil reservoir sight glass (see

Figure 4-6 on page 42). Refill as necessary.

2. Check the Air Caddy particulate filter trap sight

glass. Empty as necessary.

5.3.2

Checking the Air Caddy drop-out
circuit

The Air Caddy drop-out circuit prevents the machine
from restarting unexpectedly after the air supply to the
Air Caddy is lost and restored.
Do the following to check the Air Caddy drop-out cir-
cuit:

1. Check that the Air Caddy is connected to a shop

air supply and the ODF Speed Facer.

2. Check that the air-supply lock-out is open (that

is, pulled up). See Figure 4-6 on page 42.

ABLE

5-2. A

PPROVED

LUBRICANTS

Application Area

Lubricant

Biodegradable Lubri-

cant

Viscosity (cSt)

Quantity

Frequency

Daily

Rectangular & Dove-
tail Ways

Mobil Vactra Oil
Heavy Medium

N/A

>68 @ 40C

As required

Daily during machine
use

Each Use

Air Caddy

Mobil Almo 525 Air
Tool Oil

N/A

22-68 @ 40°C

4.3-8.7 @
100°C

Refill oil lubri-
cator

Each use

Unpainted Surfaces

LPS1 or LPS2

N/A

38 @ 25C

As required

Each use, and before
storage

Bearing surface of
track ring

LPS All-Purpose Anti-
Seize Platinum Grade

N/A

As required

Weekly during machine
use

Weekly

Lead screw on sin-
gle point tool head

NOOK E-100 spray
lube

NOOK PAG-1 grease

CASTROL BioTac EP 2

96 @ 40C

113 @ 100C

Light coating
applied by hand
or spray

Weekly during machine
use

Jacking feet

Moly Grade Anti-
Seize

N/A

1 cc per screw

Weekly during machine
use, and before storage

During Use

Bearing surface of
track ring

ThermaPlex LPS
bearing grease

N/A

6 strokes with a
standard lube
gun

Hourly during use

Use highly anti-corrosive, refined mineral or synthetic oil that forms a strong oil film and is not easily emulsified or washed away by

coolant. Hydraulic oils are typically not suitable for slide way lubrication.

Содержание H&S TOOL SPEED FACER ODF100





































































































































Результаты поиска

Содержание H&S TOOL SPEED FACER ODF100

Отзывы:

Похожие инструкции для H&S TOOL SPEED FACER ODF100

Бренды по названию

Популярные бренды

Climax H&S TOOL SPEED FACER ODF100, Руководство по эксплуатации

Результаты поиска

Содержание H&S TOOL SPEED FACER ODF100

Отзывы:

Похожие инструкции для H&S TOOL SPEED FACER ODF100

Бренды по названию

Популярные бренды