manualshive.com logo in svg

Climax H&S TOOL SPEED FACER ODF100, Руководство по эксплуатации

Поделиться
Скачать
Climax H&S TOOL SPEED FACER ODF100 Скачать руководство пользователя страница 21

P/N 102615, Rev. 0

Page 3

Machine mounting – 

Do not operate the machine 

unless mounted to a workpiece in accordance 
with this manual. If mounting the machine in an 
overhead or vertical position, do not remove 
hoist rigging until the machine is mounted to 
the workpiece in accordance with this manual. 

In any mounting position, verify that the 
machine is tethered and mounted so that if the 
machine slips or rotates, no injury or damage 
will occur.

1.5

R

ISK

 

ASSESSMENT

 

AND

 

HAZARD

 

MITIGATION

Machine Tools are specifically designed to perform pre-
cise material-removal operations.
Stationary Machine Tools include lathes and milling 
machines and are typically found in a machine shop. 
They are mounted in a fixed location during operation 
and are considered to be a complete, self-contained 
machine. Stationary Machine Tools achieve the rigidity 
needed to accomplish material-removal operations from 
the structure that is an integral part of the machine 
tool.
Portable Machine Tools are designed for on-site machin-
ing applications. They typically attach directly to the 
workpiece itself, or to an adjacent structure, and 
achieve their rigidity from the structure to which it is 
attached. The design intent is that the Portable Machine 
Tool and the structure to which it is attached become 

one complete machine during the material-removal pro-
cess.
To achieve the intended results and to promote safety, 
the operator must understand and follow the design 
intent, set-up, and operation practices that are unique 
to Portable Machine Tools.
The operator must perform an overall review and on-
site risk assessment of the intended application. Due to 
the unique nature of portable machining applications, 
identifying one or more hazards that must be addressed 
is typical. 
When performing the on-site risk assessment, it is 
important to consider the Portable Machine Tool and the 
workpiece as a whole.

Содержание H&S TOOL SPEED FACER ODF100





































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды