Clic Cardinal WD-02.2 Скачать руководство пользователя страница 2

 

Page 2 of 15 

Rev. G

 

PRECAUTIONS 

IMPORTANT SAFETY INSTRUCTIONS  

Read Instructions: 

Read all safety and operating instructions before using the device. 

Retain Instructions: 

Keep safety and operating instructions for future reference. 

Heed Warnings: 

Adhere to all warnings on the device and in the operating instructions. 

Follow Instructions:

 Follow operating instructions and installation instructions. Failure to follow these instructions 

may damage the product or void the product warranty. 

Heat: 

Keep the device away from heat sources such as radiators, heat registers, stoves, etc. 

Power Sources: 

Connect only to the power supply that was included with the device. 

Power Cord Protection: 

Route power supply cords so that they are not likely to be stepped on or pinched by items 

placed on or against them. Paying particular attention to the cords at plugs, receptacles, and at the point at which 
they connect to the device. 

Water and Moisture: 

Do not use the device near water; for example, near a sink, in a wet basement, near a 

swimming pool, near an open window, in a damp mechanical room, etc. 

Object and Liquid Entry: 

Do not allow objects to fall or liquids to be spilled into the enclosure through openings. 

Indoor Use Only: 

The device should be installed and used indoors only. Do not use the device outdoors. 

Servicing: 

There are no user serviceable parts inside of the device. Do not attempt to open the enclosure or 

perform any service beyond that described in the operating instructions. Refer all other service needs to qualified 
service personnel.  

Damage Requiring Service: 

The device should be serviced by qualified service personnel when: 

 

Objects have fallen or liquid has been spilled into the device. 

 

The power supply cord or the plug has been damaged. 

 

The device does not appear to operate normally or exhibits a marked change in performance. 

 

The device has been dropped or the enclosure has been damaged. 

 

 

WARNING! 

T

O REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK

,

 DO NOT EXPOSE THE DEVICE TO RAIN OR MOISTURE

 

SAVE THESE INSTRUCTIONS 

Содержание Cardinal WD-02.2
















Отзывы: