Clevo P6x0Hx Скачать руководство пользователя страница 187

Страница: 187 / 368

Modules

Wireless LAN Module 6 - 29

Wireless LAN Module

If you have included an

Intel

, Qualcomm Atheros or WLAN AD

combo module

is on (i.e. the system is not in

Airplane Mode

) before installing the driver.

Make sure you install the drivers in the order indicated in

Table 4 - 1, on page 4 - 4

• Note that you need to install both the WLAN & Bluetooth drivers for the

WLAN & Bluetooth Combo modules.

•

The AC/AD combo module requires both the WLAN & Bluetooth driver
installation, and also requires a WIGIg driver installation.

See the appropriate driver installation instructions on the page indicated below:

• See

“Intel® WLAN Driver Installation” on page 6 - 30

• See

“Qualcomm Atheros WLAN Combo Driver Installation” on page 6 - 30

• See

“WLAN AC/AD Combo Driver Installation” on page 6 - 31



Wireless Device

Operation Aboard

Aircraft

The use of any portable
electronic transmission
devices aboard aircraft
is usually prohibited.
Make sure the

WLAN &

Bluetooth module(s)
are OFF

if you are using

the computer aboard
aircraft by putting the
system in to

Airplane

Mode

(see

Table 1 - 6,

on page 1 - 22

Содержание P6x0Hx

















































































































































































































































































































































































Результаты поиска

Содержание P6x0Hx

Отзывы:

Похожие инструкции для P6x0Hx

Бренды по названию

Популярные бренды

Clevo P6x0Hx, Руководство пользователя

Результаты поиска

Содержание P6x0Hx

Отзывы:

Похожие инструкции для P6x0Hx

Бренды по названию

Популярные бренды