Clevo P6x0Hx Скачать руководство пользователя страница 160 | Manualshive

Страница: 160 / 368

background image

Modules

6 - 2 Setting Up SATA RAID, Optane™ or AHCI Mode

6

Setting Up SATA RAID, Optane™ or AHCI Mode

Note that your system can be set up as a RAID OR to support Intel® Optane™,
it cannot be set to support both systems.

AHCI Mode

Advanced Host Controller Interface (AHCI) is an interface specification that allows
the storage driver to enable advanced serial ATA features such as Native Command
Queuing (for maximum hard disk efficiency and performance). AHCI mode can be
supported by one or two hard disks/solid state drives. Make sure you install the

In-

tel® Rapid Storage Technology

application if you have set up your HDDs/SSDs

in

AHCI

mode (see

“Intel® Rapid Storage Technology” on page 6 - 56

Intel® Optane™

Intel® Optane™

is a combination of a compatible memory device and

Intel Rapid

Technology software

. This combination is designed to speed up your system per-

formance by caching boot data, executables, frequently accessed data and system
page files to an non volatile, low latency Intel® Optane™ SSD.

Contact your distributor or supplier to see if your system supports this technology.

RAID

To configure your RAID (Redundant Array of Independent Disks) system in Strip-
ing (RAID 0) or Mirroring (RAID 1) modes (see

Table 6 - 1, on page 6 - 4

) you will

require

at least

two

identical

(see sidebar) HDDs/SSDs.



RAID Hard Disks/

Solid State Drives

All HDDS/SSDs in a
RAID should be identi-
cal (the same size and
brand) in order to pre-
vent unexpected system
behavior.

SATA Mode

Selection

The SATA mode selec-
tion should be made

be-

fore installing your
operating system

.

DO NOT change your
selected SATA mode

unless you intend to re-
install your operating
system. Make sure you
have backed up all your
data before doing so.

«
...
158
159
160
161
162
...
»

Содержание P6x0Hx

















































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для P6x0Hx

Aspire 1670 Series

Бренд: Acer Страницы: 118

Бренд: Acer Страницы: 94

AcerNote Nuovo 970

Бренд: Acer Страницы: 4

Бренд: Acer Страницы: 16

9410-2829 - Aspire

Бренд: Acer Страницы: 108

Бренд: Acer Страницы: 130

Бренд: Acer Страницы: 93

Aspire 1360 Series

Бренд: Acer Страницы: 104

Barbie B-Glam LC68-12

Бренд: Oregon Scientific Страницы: 2

Бренд: Acer Страницы: 92

MX6440 - Notebook Computer

Бренд: Gateway Страницы: 1

Бренд: Sony Страницы: 2

MZ-R30 Analog PCLink

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 16

Бренд: Sony Страницы: 20

Бренд: Sony Страницы: 26

Бренд: Sony Страницы: 40

Бренд: Sony Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды