1943049
V1.4
November 2018
Testing:
Once connected to the 240V mains supply, the unit must be allowed to charge the battery for at least 24
hours. Conduct the following tests:
•
For the first test, the emergency lamp must remain illuminated for at least 2 hours after disconnection
from the mains supply.
•
Subsequent tests require the unit to illuminate for at least 90 minutes. The results of all tests are
required to be recorded in a service logbook, which is to be kept on-site at all times. If the unit fails to
remain illuminated for the requisite time, remedial action must be taken to repair the situation and
once completed, the unit must pass a subsequent test. For more specific information, please refer to
the current edition of the AS 2293.3 Standard.
Ultrablade Maintenance:
LED Lamp Replacement:
•
Use only the LED Strip recommended in the
Spares Parts list of this instruction.
•
Disconnect battery from LED driver.
•
Remove the screw holding the driver PCA.
Remove the PCA.
•
Remove the 4 screws holding the battery
bracket. Remove the bracket with the battery.
•
Disconnect the signal cable from LED strip.
•
Remove 4 self-tapping screws and unclip the
LED strip.
•
Install the new LED strip following the above
procedure in reverse.
Battery Replacement:
•
Use only the battery recommended in the
Spares List on this instruction.
•
Remove the battery from battery
compartment, un-plug the lead from the
battery connector remove the old battery.
•
Plug the new battery into the battery
connector.
•
Secure the battery into the battery
compartment
Trouble Shooting:
Below are a list of common problems and their
possible causes.
Fault:
The Green LED Test Switch indicator
is not illuminated.
Check: A.C. is connected and is turned on.
Battery is connected
Test Switch for damage.
Fault:
Lamp does not illuminate in
emergency mode.
Check: A.C. is connected.
Lamp is correctly inserted.
Battery is connected
Fault:
Lamp illuminates in emergency mode,
but only stays on for a short period.
Check:
Battery has been allowed to charge for at
least 24 hours.
Battery for damage.
Rated Emergency Lumen Output in accordance with AS2293.1 (refer to
spacing tables for installation positions), not Included
–TH version:
C0=E6.3 (8m) C90=E6.3 (8m)
Caution:
On many building sites, power circuits may be cut off in an uncontrolled and repetitive basis during
construction. As a result, any Exit & Emergency Units, on these circuits, will have their batteries
discharged or “cycled”. The battery in this fitting has been selected to give excellent long-life performance
in a controlled AS2293 testing environment. Excessive battery cycling will reduce through-life
performance and may lead to premature battery failure. Battery warranty claims, as a result of such
abuse, are specifically EXCLUDED from Clevertronics warranty terms.
Warranty:
For Product Warranty information and Terms and Conditions of Sales please refer to our website
http://clevertronics.com.au/terms-conditions-sale-australia-nz
LP
™
Ultrablade Pro Surface Mount LED Exit
Installation & Maintenance Instruction Leaflet
Victoria (Head Office & Manufacturing)
195 Chesterville Rd
Moorabbin VIC 3189
Phone:
+61 3 9559 2700
Fax:
+61 3 9559 2799
New South Wales
Phone:
+61 2 8805 6400
Fax:
+61 2 8805 6444
Queensland
Phone:
+61 7 3442 9700
Fax:
+61 7 3442 9777
South Australia/Northern Territory
Phone:
+61 8 8301 8800
Fax:
+61 8 8351 8286
Western Australia
Phone:
+61 8 9248 3720
Fax:
+61 8 9248 3725
New Zealand
Phone: +64
800 548 448
Designed in Australia to comply with the requirements
of AS2293.3:2005 and AS/NZ CISPR:15
Models: CUBPRO-SM-ww-xx-yy-zz
Testing:
Options:
Manual Test
xx = Blank
Black Body
yy = BLK
Zoneworks
xx = ZW
Theatre Decal
ww = Theatre
Z/W DATA
xx = DATA
Running Man
zz = R
DALI Comp.
xx = DALI
Running Man Right
zz = RR
Clevertest
xx = CT
Running Man Left
zz = RL
Double Side Running Man
zz = DS-R
(NOTE: -CT Products supplied with the Clevertest Plus Symbol are activated with Clevertest
PLUS capability. Please refer to the operation guide supplied with the product for details).
Spare Parts:
1550105
– Battery, 3.2 Volt 1.1Ah Li-ion
8002178
– PCA: UBP LED strip PCB Assy
8002946 - PCA:
PCA:C/LUBPRO-SM-TH-DS-R
(for -TH-DS Option only)
8002945
– PCA: L/CUBPRO-SM #CT10142-L8 CTP
Important:
It is illegal for anyone, except for a licensed electrician to install or maintain this product. Before installation,
ensure that the electricity supply has been switched off and isolated. Installation must be carried out in
accordance with the relevant Australian and International Standards.
NOTE: Standard product codes with this symbol
are enabled with Clevertest Plus capability.
Please refer to the operation guide supplied with
the product for details.