Nederlands
Nederlands
32
33
Artikelnummer: 2608
WERKINGEN
Voor het eerste gebruik
• Haal de stoombezem en accessoires voorzichtig uit de verpakking en controleer het apparaat op volledigheid en
beschadiging. Gebruik geen beschadigde onderdelen. Neem in dat geval contact op met de klantenservice.
• Verwijder alle transportverpakkingen en beschermfolies van de stoombezem en accessoires.
Er kunnen waterresten in het waterreservoir zitten. Dit is geen gebrek.
Dit toont alleen aan dat het apparaat is getest door de afdeling kwaliteitsborging.
Assemblage
1. Steek de hoofdeenheid [A] in de houder [B] totdat u hoort dat deze op zijn plaats klikt.
U kunt de hoofdeenheid [A] weer verwijderen door op de vergrendelknop [6] te drukken.
2. Druk het vasthoudmechanisme [B] op de stoomvoet [M] tot deze vastklikt.
Door op de ont- grendelingsknop aan de achterzijde te drukken,
kunt u de stoomvoet [M] uit de houder [B] halen.
3. Klap het handvat [2] naar boven totdat je het hoort klikken.
Klap de handgreep [2] samen met de vergrendelknop op het scharniergewricht [1] weer terug.
4. Trek het antivirale ruitenwisserdeksel [K] over de stoomvoet [M] en zet het vast met het koord.
5. Om tapijten te reinigen, plaatst u de tapijtschuif [N] op de stoomvoet [M].
Wij raden aan de te reinigen oppervlakken grondig te stofzuigen of te ontdoen
van kruimels en dergelijke alvorens de stoombezem te gebruiken.
Het vullen van de watertank
Methode 1 - Vul het geplaatste waterreservoir
1. Draai het deksel van het waterreservoir [13] tegen de wijzers van de
klok in om het waterre- servoir te openen [15].
2. Vul het waterreservoir [15] met de bijgeleverde maatbeker [J].
3. Plaats het deksel [13] en schroef het terug door
het met de klok mee te draaien.
Methode 2 - Vul het verwijderde waterreservoir
1. Trek het waterreservoir [15] uit de hoofdeenheid [A] door beide vergrendelknoppen
op het wa- terreservoir [14] in te drukken en vast te houden.
2. Draai het deksel van het waterreservoir [15] tegen de wijzers van de klok in om
het waterre- servoir te openen [15].
3. Houd het waterreservoir [15] onder een waterkraan en vul het.
4. Plaats het deksel [13] en schroef het terug met de klok mee.
5. Steek het waterreservoir terug in de hoofdeenheid [A] tot het met een schop op zijn plaats klikt.
Stoomreiniging van oppervlakken
1. Steek de stekker in een stopcontact.
2. Schakel het apparaat in met de aan/uit-knop [9].
3. De lampen [10] beginnen rood op te lichten, wat aangeeft dat de stoombezem zich in de opwarmfase bevindt.
Het opwarmen duurt ongeveer 25 seconden. Zodra de lampen [10] blauw oplichten, is het apparaat klaar voor gebruik.
Een volle watertank is voldoende voor ongeveer 20 minuten.
Als de stroomtoevoer tijdens of na het voorverwarmen wordt onderbroken, zal het toestel de hierboven beschreven verwar-
mingsprocedure herhalen.
4. U kunt de hoeveelheid stoom regelen met de stoomregelaar [12].
Draai de regelaar tegen de klok in om het stoomdebiet te verminderen en met de
klok mee om het stoomdebiet te verhogen.
5. Plaats de stoomvoet op de vloer en kantel de stoomborstel iets terug.
De
utsc
h
NOTE:
Each steam mop is 100% tested in the factory to ensure product performance and
safety.When assembling your new steam mop for the first time you may notice water residue
inside of the unit.
!WARNING:
Before attempting any of the following operations,make sure that the appliance is
switched off and unplugged and that the appliance is cold and contains minimal or no water.
Spread holder
Round the holder along spindle until click to fix holder.
Press spindle button 1,turn the holder,the holder can become folded state.
Attaching the steam head
Slide the bottom end of main body onto
the steam head M until Steam head Spindle 5
clicks into place
The steam head M can be removed from the
Main body by pressing salient point on the
Steam head Spindle 5
Attaching a cleaning pad
Because of barb design at the bottom of steam head M,just
place a micro-fiber cleaning pad L to steam had,they can
bond hard.
Place the front of your shoe onto the cleaning pad removal
Tab and press down firmly.
Attaching Carpet Gilder
Press the micro-fiber cleaning pad L with main body to
Carpet gilder O by vertical pressure
，
until it into place.
Place the front of your shoe onto the cleaning pad removal
Tab and press down firmly,carpet gilder will remove form
steam head
Page 5 of 10
NOTE:
Each steam mop is 100% tested in the factory to ensure product performance and
safety.When assembling your new steam mop for the first time you may notice water residue
inside of the unit.
!WARNING:
Before attempting any of the following operations,make sure that the appliance is
switched off and unplugged and that the appliance is cold and contains minimal or no water.
Spread holder
Round the holder along spindle until click to fix holder.
Press spindle button 1,turn the holder,the holder can become folded state.
Attaching the steam head
Slide the bottom end of main body onto
the steam head M until Steam head Spindle 5
clicks into place
The steam head M can be removed from the
Main body by pressing salient point on the
Steam head Spindle 5
Attaching a cleaning pad
Because of barb design at the bottom of steam head M,just
place a micro-fiber cleaning pad L to steam had,they can
bond hard.
Place the front of your shoe onto the cleaning pad removal
Tab and press down firmly.
Attaching Carpet Gilder
Press the micro-fiber cleaning pad L with main body to
Carpet gilder O by vertical pressure
，
until it into place.
Place the front of your shoe onto the cleaning pad removal
Tab and press down firmly,carpet gilder will remove form
steam head
Page 5 of 10
ASSEMBLY
NOTE:
Each steam mop is 100% tested in the factory to ensure product performance and
safety.When assembling your new steam mop for the first time you may notice water residue
inside of the unit.
!WARNING:
Before attempting any of the following operations,make sure that the appliance is
switched off and unplugged and that the appliance is cold and contains minimal or no water.
Spread holder
Round the holder along spindle until click to fix holder.
Press spindle button 1,turn the holder,the holder can become folded state.
Attaching the steam head
Slide the bottom end of main body onto
the steam head M until Steam head Spindle 5
clicks into place
The steam head M can be removed from the
Main body by pressing salient point on the
Steam head Spindle 5
Attaching a cleaning pad
Because of barb design at the bottom of steam head M,just
place a micro-fiber cleaning pad L to steam had,they can
bond hard.
Place the front of your shoe onto the cleaning pad removal
Tab and press down firmly.
Attaching Carpet Gilder
Press the micro-fiber cleaning pad L with main body to
Carpet gilder O by vertical pressure
，
until it into place.
Place the front of your shoe onto the cleaning pad removal
Tab and press down firmly,carpet gilder will remove form
steam head
Page 5 of 10
ASSEMBLY
NOTE:
Each steam mop is 100% tested in the factory to ensure product performance and
safety.When assembling your new steam mop for the first time you may notice water residue
inside of the unit.
!WARNING:
Before attempting any of the following operations,make sure that the appliance is
switched off and unplugged and that the appliance is cold and contains minimal or no water.
Spread holder
Round the holder along spindle until click to fix holder.
Press spindle button 1,turn the holder,the holder can become folded state.
Attaching the steam head
Slide the bottom end of main body onto
the steam head M until Steam head Spindle 5
clicks into place
The steam head M can be removed from the
Main body by pressing salient point on the
Steam head Spindle 5
Attaching a cleaning pad
Because of barb design at the bottom of steam head M,just
place a micro-fiber cleaning pad L to steam had,they can
bond hard.
Place the front of your shoe onto the cleaning pad removal
Tab and press down firmly.
Attaching Carpet Gilder
Press the micro-fiber cleaning pad L with main body to
Carpet gilder O by vertical pressure
，
until it into place.
Place the front of your shoe onto the cleaning pad removal
Tab and press down firmly,carpet gilder will remove form
steam head
Page 5 of 10
Method one:
：
Open the water tank cup 5 by counterclockwise
rotation,fill 360ML water use Measuring cup,
and then clockwise rotation to close water tank cup 5.
Method two
：
Remove the water tank from main body,open the
water tank cup 5 by counterclockwise rotation,fill
the water tank from water faucet.,and then clockwise
rotation to close water tank cup 5.
Install the water tank 7to main body until it clicks into place.
2.Plug in the appliance to a grounded outlet.
3.When switch the appliance on,the indicator lights will turn red at the each side of water tank,it
indicate preheating.If the lights does not illuminate,please check the "troubleshooting" section for
more details.
4.It will takes approximately 25 seconds for preheating.Once the steam mop is ready to use the
water tank will glow blue.
5.When the water tank full fill with water,it can work approximately 20 minutes.If the water tank
7 without water,the indicator lights 12 will glow red,and the lights will flash to point out need to
add water
NOTICE
：
If power off during preheating or after preheating,then power again,the
appliance will repeat above preheating action.
6.Press the steam button 4 and steam button13,the steam out.
7.Add control volume by turn steam control knob 8
lockwise
，
and counterclockwise to reduce
，
User
can adjust steam volume according different objects
NOTICE
：
steam volume control by PCB,It will takes 3 seconds adaptation time
when you adjust steam volume .It is normal phenomenon.
8. When normal cleaning,the steam head
has big rotary angle,can clean corners
nd also can clean low space.
USE AS A STEAM CLEANER IN HAND
Push Lock Catch,take the main body A out of holder A,and also take out the power cord.
Install the accessory adaptor at the top of main body A,until it into place.
Press salient point at the accessory adaptor to remove the accessory adaptor from main body
A
Choose the appropriate accessories(check accessories use list),according to arrow indicator to
align and implant to accessory adaptor G,then turn anticlockwise,until it into place.
Page 6 of 10
rotation,fill 360ML water use Measuring cup,
and then clockwise rotation to close water tank cup 5.
Method two
：
Remove the water tank from main body,open the
water tank cup 5 by counterclockwise rotation,fill
the water tank from water faucet.,and then clockwise
rotation to close water tank cup 5.
Install the water tank 7to main body until it clicks into place.
2.Plug in the appliance to a grounded outlet.
3.When switch the appliance on,the indicator lights will turn red at the each side of water tank,it
indicate preheating.If the lights does not illuminate,please check the "troubleshooting" section for
more details.
4.It will takes approximately 25 seconds for preheating.Once the steam mop is ready to use the
water tank will glow blue.
5.When the water tank full fill with water,it can work approximately 20 minutes.If the water tank
7 without water,the indicator lights 12 will glow red,and the lights will flash to point out need to
add water
NOTICE
：
If power off during preheating or after preheating,then power again,the
appliance will repeat above preheating action.
6.Press the steam button 4 and steam button13,the steam out.
7.Add control volume by turn steam control knob 8
clockwise
，
and counterclockwise to reduce
，
User
can adjust steam volume according different objects
NOTICE
：
steam volume control by PCB,It will takes 3 seconds adaptation time
when you adjust steam volume .It is normal phenomenon.
8. When normal cleaning,the steam head
has big rotary angle,can clean corners
and also can clean low space.
USE AS A STEAM CLEANER IN HAND
Push Lock Catch,take the main body A out of holder A,and also take out the power cord.
Install the accessory adaptor at the top of main body A,until it into place.
Press salient point at the accessory adaptor to remove the accessory adaptor from main body
A
Choose the appropriate accessories(check accessories use list),according to arrow indicator to
align and implant to accessory adaptor G,then turn anticlockwise,until it into place.
Page 6 of 10
OPERATION
1.Filling the water tank
Method one:
：
Open the water tank cup 5 by counterclockwise
rotation,fill 360ML water use Measuring cup,
and then clockwise rotation to close water tank cup 5.
Method two
：
Remove the water tank from main body,open the
water tank cup 5 by counterclockwise rotation,fill
the water tank from water faucet.,and then clockwise
rotation to close water tank cup 5.
Install the water tank 7to main body until it clicks into place.
2.Plug in the appliance to a grounded outlet.
3.When switch the appliance on,the indicator lights will turn red at the each side of water tank,it
indicate preheating.If the lights does not illuminate,please check the "troubleshooting" section for
more details.
4.It will takes approximately 25 seconds for preheating.Once the steam mop is ready to use the
water tank will glow blue.
5.When the water tank full fill with water,it can work approximately 20 minutes.If the water tank
7 without water,the indicator lights 12 will glow red,and the lights will flash to point out need to
add water
NOTICE
：
If power off during preheating or after preheating,then power again,the
appliance will repeat above preheating action.
6.Press the steam button 4 and steam button13,the steam out.
7.Add control volume by turn steam control knob 8
clockwise
，
and counterclockwise to reduce
，
User
can adjust steam volume according different objects
NOTICE
：
steam volume control by PCB,It will takes 3 seconds adaptation time
when you adjust steam volume .It is normal phenomenon.
8. When normal cleaning,the steam head
has big rotary angle,can clean corners
and also can clean low space.
USE AS A STEAM CLEANER IN HAND
Push Lock Catch,take the main body A out of holder A,and also take out the power cord.
Install the accessory adaptor at the top of main body A,until it into place.
Press salient point at the accessory adaptor to remove the accessory adaptor from main body
A
Choose the appropriate accessories(check accessories use list),according to arrow indicator to
align and implant to accessory adaptor G,then turn anticlockwise,until it into place.
Page 6 of 10
De
utsc
h
NOTE:
Each steam mop is 100% tested in the factory to ensure product performance and
safety.When assembling your new steam mop for the first time you may notice water residue
inside of the unit.
!WARNING:
Before attempting any of the following operations,make sure that the appliance is
switched off and unplugged and that the appliance is cold and contains minimal or no water.
Spread holder
Round the holder along spindle until click to fix holder.
Press spindle button 1,turn the holder,the holder can become folded state.
Attaching the steam head
Slide the bottom end of main body onto
the steam head M until Steam head Spindle 5
clicks into place
The steam head M can be removed from the
Main body by pressing salient point on the
Steam head Spindle 5
Attaching a cleaning pad
Because of barb design at the bottom of steam head M,just
place a micro-fiber cleaning pad L to steam had,they can
bond hard.
Place the front of your shoe onto the cleaning pad removal
Tab and press down firmly.
Attaching Carpet Gilder
Press the micro-fiber cleaning pad L with main body to
Carpet gilder O by vertical pressure
，
until it into place.
Place the front of your shoe onto the cleaning pad removal
Tab and press down firmly,carpet gilder will remove form
steam head
Page 5 of 10
NOTE:
Each steam mop is 100% tested in the factory to ensure product performance and
safety.When assembling your new steam mop for the first time you may notice water residue
inside of the unit.
!WARNING:
Before attempting any of the following operations,make sure that the appliance is
switched off and unplugged and that the appliance is cold and contains minimal or no water.
Spread holder
Round the holder along spindle until click to fix holder.
Press spindle button 1,turn the holder,the holder can become folded state.
Attaching the steam head
Slide the bottom end of main body onto
the steam head M until Steam head Spindle 5
clicks into place
The steam head M can be removed from the
Main body by pressing salient point on the
Steam head Spindle 5
Attaching a cleaning pad
Because of barb design at the bottom of steam head M,just
place a micro-fiber cleaning pad L to steam had,they can
bond hard.
Place the front of your shoe onto the cleaning pad removal
Tab and press down firmly.
Attaching Carpet Gilder
Press the micro-fiber cleaning pad L with main body to
Carpet gilder O by vertical pressure
，
until it into place.
Place the front of your shoe onto the cleaning pad removal
Tab and press down firmly,carpet gilder will remove form
steam head
Page 5 of 10
ASSEMBLY
NOTE:
Each steam mop is 100% tested in the factory to ensure product performance and
safety.When assembling your new steam mop for the first time you may notice water residue
inside of the unit.
!WARNING:
Before attempting any of the following operations,make sure that the appliance is
switched off and unplugged and that the appliance is cold and contains minimal or no water.
Spread holder
Round the holder along spindle until click to fix holder.
Press spindle button 1,turn the holder,the holder can become folded state.
Attaching the steam head
Slide the bottom end of main body onto
the steam head M until Steam head Spindle 5
clicks into place
The steam head M can be removed from the
Main body by pressing salient point on the
Steam head Spindle 5
Attaching a cleaning pad
Because of barb design at the bottom of steam head M,just
place a micro-fiber cleaning pad L to steam had,they can
bond hard.
Place the front of your shoe onto the cleaning pad removal
Tab and press down firmly.
Attaching Carpet Gilder
Press the micro-fiber cleaning pad L with main body to
Carpet gilder O by vertical pressure
，
until it into place.
Place the front of your shoe onto the cleaning pad removal
Tab and press down firmly,carpet gilder will remove form
steam head
Page 5 of 10
ASSEMBLY
NOTE:
Each steam mop is 100% tested in the factory to ensure product performance and
safety.When assembling your new steam mop for the first time you may notice water residue
inside of the unit.
!WARNING:
Before attempting any of the following operations,make sure that the appliance is
switched off and unplugged and that the appliance is cold and contains minimal or no water.
Spread holder
Round the holder along spindle until click to fix holder.
Press spindle button 1,turn the holder,the holder can become folded state.
Attaching the steam head
Slide the bottom end of main body onto
the steam head M until Steam head Spindle 5
clicks into place
The steam head M can be removed from the
Main body by pressing salient point on the
Steam head Spindle 5
Attaching a cleaning pad
Because of barb design at the bottom of steam head M,just
place a micro-fiber cleaning pad L to steam had,they can
bond hard.
Place the front of your shoe onto the cleaning pad removal
Tab and press down firmly.
Attaching Carpet Gilder
Press the micro-fiber cleaning pad L with main body to
Carpet gilder O by vertical pressure
，
until it into place.
Place the front of your shoe onto the cleaning pad removal
Tab and press down firmly,carpet gilder will remove form
steam head
Page 5 of 10
Method one:
：
Open the water tank cup 5 by counterclockwise
rotation,fill 360ML water use Measuring cup,
and then clockwise rotation to close water tank cup 5.
Method two
：
Remove the water tank from main body,open the
water tank cup 5 by counterclockwise rotation,fill
the water tank from water faucet.,and then clockwise
rotation to close water tank cup 5.
Install the water tank 7to main body until it clicks into place.
2.Plug in the appliance to a grounded outlet.
3.When switch the appliance on,the indicator lights will turn red at the each side of water tank,it
indicate preheating.If the lights does not illuminate,please check the "troubleshooting" section for
more details.
4.It will takes approximately 25 seconds for preheating.Once the steam mop is ready to use the
water tank will glow blue.
5.When the water tank full fill with water,it can work approximately 20 minutes.If the water tank
7 without water,the indicator lights 12 will glow red,and the lights will flash to point out need to
add water
NOTICE
：
If power off during preheating or after preheating,then power again,the
appliance will repeat above preheating action.
6.Press the steam button 4 and steam button13,the steam out.
7.Add control volume by turn steam control knob 8
lockwise
，
and counterclockwise to reduce
，
User
can adjust steam volume according different objects
NOTICE
：
steam volume control by PCB,It will takes 3 seconds adaptation time
when you adjust steam volume .It is normal phenomenon.
8. When normal cleaning,the steam head
has big rotary angle,can clean corners
nd also can clean low space.
USE AS A STEAM CLEANER IN HAND
Push Lock Catch,take the main body A out of holder A,and also take out the power cord.
Install the accessory adaptor at the top of main body A,until it into place.
Press salient point at the accessory adaptor to remove the accessory adaptor from main body
A
Choose the appropriate accessories(check accessories use list),according to arrow indicator to
align and implant to accessory adaptor G,then turn anticlockwise,until it into place.
Page 6 of 10
rotation,fill 360ML water use Measuring cup,
and then clockwise rotation to close water tank cup 5.
Method two
：
Remove the water tank from main body,open the
water tank cup 5 by counterclockwise rotation,fill
the water tank from water faucet.,and then clockwise
rotation to close water tank cup 5.
Install the water tank 7to main body until it clicks into place.
2.Plug in the appliance to a grounded outlet.
3.When switch the appliance on,the indicator lights will turn red at the each side of water tank,it
indicate preheating.If the lights does not illuminate,please check the "troubleshooting" section for
more details.
4.It will takes approximately 25 seconds for preheating.Once the steam mop is ready to use the
water tank will glow blue.
5.When the water tank full fill with water,it can work approximately 20 minutes.If the water tank
7 without water,the indicator lights 12 will glow red,and the lights will flash to point out need to
add water
NOTICE
：
If power off during preheating or after preheating,then power again,the
appliance will repeat above preheating action.
6.Press the steam button 4 and steam button13,the steam out.
7.Add control volume by turn steam control knob 8
clockwise
，
and counterclockwise to reduce
，
User
can adjust steam volume according different objects
NOTICE
：
steam volume control by PCB,It will takes 3 seconds adaptation time
when you adjust steam volume .It is normal phenomenon.
8. When normal cleaning,the steam head
has big rotary angle,can clean corners
and also can clean low space.
USE AS A STEAM CLEANER IN HAND
Push Lock Catch,take the main body A out of holder A,and also take out the power cord.
Install the accessory adaptor at the top of main body A,until it into place.
Press salient point at the accessory adaptor to remove the accessory adaptor from main body
A
Choose the appropriate accessories(check accessories use list),according to arrow indicator to
align and implant to accessory adaptor G,then turn anticlockwise,until it into place.
Page 6 of 10
OPERATION
1.Filling the water tank
Method one:
：
Open the water tank cup 5 by counterclockwise
rotation,fill 360ML water use Measuring cup,
and then clockwise rotation to close water tank cup 5.
Method two
：
Remove the water tank from main body,open the
water tank cup 5 by counterclockwise rotation,fill
the water tank from water faucet.,and then clockwise
rotation to close water tank cup 5.
Install the water tank 7to main body until it clicks into place.
2.Plug in the appliance to a grounded outlet.
3.When switch the appliance on,the indicator lights will turn red at the each side of water tank,it
indicate preheating.If the lights does not illuminate,please check the "troubleshooting" section for
more details.
4.It will takes approximately 25 seconds for preheating.Once the steam mop is ready to use the
water tank will glow blue.
5.When the water tank full fill with water,it can work approximately 20 minutes.If the water tank
7 without water,the indicator lights 12 will glow red,and the lights will flash to point out need to
add water
NOTICE
：
If power off during preheating or after preheating,then power again,the
appliance will repeat above preheating action.
6.Press the steam button 4 and steam button13,the steam out.
7.Add control volume by turn steam control knob 8
clockwise
，
and counterclockwise to reduce
，
User
can adjust steam volume according different objects
NOTICE
：
steam volume control by PCB,It will takes 3 seconds adaptation time
when you adjust steam volume .It is normal phenomenon.
8. When normal cleaning,the steam head
has big rotary angle,can clean corners
and also can clean low space.
USE AS A STEAM CLEANER IN HAND
Push Lock Catch,take the main body A out of holder A,and also take out the power cord.
Install the accessory adaptor at the top of main body A,until it into place.
Press salient point at the accessory adaptor to remove the accessory adaptor from main body
A
Choose the appropriate accessories(check accessories use list),according to arrow indicator to
align and implant to accessory adaptor G,then turn anticlockwise,until it into place.
Page 6 of 10
Method one:
：
Open the water tank cup 5 by counterclockwise
rotation,fill 360ML water use Measuring cup,
and then clockwise rotation to close water tank cup 5.
Method two
：
Remove the water tank from main body,open the
water tank cup 5 by counterclockwise rotation,fill
the water tank from water faucet.,and then clockwise
rotation to close water tank cup 5.
Install the water tank 7to main body until it clicks into place.
2.Plug in the appliance to a grounded outlet.
3.When switch the appliance on,the indicator lights will turn red at the each side of water tank,it
indicate preheating.If the lights does not illuminate,please check the "troubleshooting" section for
more details.
4.It will takes approximately 25 seconds for preheating.Once the steam mop is ready to use the
water tank will glow blue.
5.When the water tank full fill with water,it can work approximately 20 minutes.If the water tank
7 without water,the indicator lights 12 will glow red,and the lights will flash to point out need to
add water
NOTICE
：
If power off during preheating or after preheating,then power again,the
appliance will repeat above preheating action.
6.Press the steam button 4 and steam button13,the steam out.
7.Add control volume by turn steam control knob 8
lockwise
，
and counterclockwise to reduce
，
User
can adjust steam volume according different objects
NOTICE
：
steam volume control by PCB,It will takes 3 seconds adaptation time
when you adjust steam volume .It is normal phenomenon.
8. When normal cleaning,the steam head
has big rotary angle,can clean corners
nd also can clean low space.
USE AS A STEAM CLEANER IN HAND
Push Lock Catch,take the main body A out of holder A,and also take out the power cord.
Install the accessory adaptor at the top of main body A,until it into place.
Press salient point at the accessory adaptor to remove the accessory adaptor from main body
A
Choose the appropriate accessories(check accessories use list),according to arrow indicator to
align and implant to accessory adaptor G,then turn anticlockwise,until it into place.
Page 6 of 10
rotation,fill 360ML water use Measuring cup,
and then clockwise rotation to close water tank cup 5.
Method two
：
Remove the water tank from main body,open the
water tank cup 5 by counterclockwise rotation,fill
the water tank from water faucet.,and then clockwise
rotation to close water tank cup 5.
Install the water tank 7to main body until it clicks into place.
2.Plug in the appliance to a grounded outlet.
3.When switch the appliance on,the indicator lights will turn red at the each side of water tank,it
indicate preheating.If the lights does not illuminate,please check the "troubleshooting" section for
more details.
4.It will takes approximately 25 seconds for preheating.Once the steam mop is ready to use the
water tank will glow blue.
5.When the water tank full fill with water,it can work approximately 20 minutes.If the water tank
7 without water,the indicator lights 12 will glow red,and the lights will flash to point out need to
add water
NOTICE
：
If power off during preheating or after preheating,then power again,the
appliance will repeat above preheating action.
6.Press the steam button 4 and steam button13,the steam out.
7.Add control volume by turn steam control knob 8
clockwise
，
and counterclockwise to reduce
，
User
can adjust steam volume according different objects
NOTICE
：
steam volume control by PCB,It will takes 3 seconds adaptation time
when you adjust steam volume .It is normal phenomenon.
8. When normal cleaning,the steam head
has big rotary angle,can clean corners
and also can clean low space.
USE AS A STEAM CLEANER IN HAND
Push Lock Catch,take the main body A out of holder A,and also take out the power cord.
Install the accessory adaptor at the top of main body A,until it into place.
Press salient point at the accessory adaptor to remove the accessory adaptor from main body
A
Choose the appropriate accessories(check accessories use list),according to arrow indicator to
align and implant to accessory adaptor G,then turn anticlockwise,until it into place.
Page 6 of 10
OPERATION
1.Filling the water tank
Method one:
：
Open the water tank cup 5 by counterclockwise
rotation,fill 360ML water use Measuring cup,
and then clockwise rotation to close water tank cup 5.
Method two
：
Remove the water tank from main body,open the
water tank cup 5 by counterclockwise rotation,fill
the water tank from water faucet.,and then clockwise
rotation to close water tank cup 5.
Install the water tank 7to main body until it clicks into place.
2.Plug in the appliance to a grounded outlet.
3.When switch the appliance on,the indicator lights will turn red at the each side of water tank,it
indicate preheating.If the lights does not illuminate,please check the "troubleshooting" section for
more details.
4.It will takes approximately 25 seconds for preheating.Once the steam mop is ready to use the
water tank will glow blue.
5.When the water tank full fill with water,it can work approximately 20 minutes.If the water tank
7 without water,the indicator lights 12 will glow red,and the lights will flash to point out need to
add water
NOTICE
：
If power off during preheating or after preheating,then power again,the
appliance will repeat above preheating action.
6.Press the steam button 4 and steam button13,the steam out.
7.Add control volume by turn steam control knob 8
clockwise
，
and counterclockwise to reduce
，
User
can adjust steam volume according different objects
NOTICE
：
steam volume control by PCB,It will takes 3 seconds adaptation time
when you adjust steam volume .It is normal phenomenon.
8. When normal cleaning,the steam head
has big rotary angle,can clean corners
and also can clean low space.
USE AS A STEAM CLEANER IN HAND
Push Lock Catch,take the main body A out of holder A,and also take out the power cord.
Install the accessory adaptor at the top of main body A,until it into place.
Press salient point at the accessory adaptor to remove the accessory adaptor from main body
A
Choose the appropriate accessories(check accessories use list),according to arrow indicator to
align and implant to accessory adaptor G,then turn anticlockwise,until it into place.
Page 6 of 10
6. Druk op de stoomknop [4] op het handvat en houd deze ingedrukt om stoom te laten ontsnappen.
Dit duurt een paar seconden. Voor de volledige reinigingskracht, stoom de droge antivirale doek [K]
gedurende ongeveer 30 seconden. Druk tijdens het reinigen slechts met tussenpozen op de stoomknop [4]
om te voorkomen dat de antivirale mop te nat wordt.
6. Maak de vloer schoon.
7. Druk nogmaals op de aan/uit-knop [9] om de stoomklopper uit te schakelen.
De aanpassingstijd voor het instellen van de stoom is ongeveer drie seconden. Bij het reinigen moet de stoomvoet niet lang
op dezelfde plaats staan en altijd in beweging zijn. Zo vermijd je overbevochtiging.
Als er tijdens het reinigingsproces onverwacht water of stoom uit onbedoelde plaatsen ontsnapt, dient u de werking onmid-
dellijk te stoppen en de stekker uit het stopcontact te trekken. Neem contact op met de klantenservice!
Method one:
：
Open the water tank cup 5 by counterclockwise
rotation,fill 360ML water use Measuring cup,
and then clockwise rotation to close water tank cup 5.
Method two
：
Remove the water tank from main body,open the
water tank cup 5 by counterclockwise rotation,fill
the water tank from water faucet.,and then clockwise
rotation to close water tank cup 5.
Install the water tank 7to main body until it clicks into place.
2.Plug in the appliance to a grounded outlet.
3.When switch the appliance on,the indicator lights will turn red at the each side of water tank,it
indicate preheating.If the lights does not illuminate,please check the "troubleshooting" section for
more details.
4.It will takes approximately 25 seconds for preheating.Once the steam mop is ready to use the
water tank will glow blue.
5.When the water tank full fill with water,it can work approximately 20 minutes.If the water tank
7 without water,the indicator lights 12 will glow red,and the lights will flash to point out need to
add water
NOTICE
：
If power off during preheating or after preheating,then power again,the
appliance will repeat above preheating action.
6.Press the steam button 4 and steam button13,the steam out.
7.Add control volume by turn steam control knob 8
lockwise
，
and counterclockwise to reduce
，
User
can adjust steam volume according different objects
NOTICE
：
steam volume control by PCB,It will takes 3 seconds adaptation time
when you adjust steam volume .It is normal phenomenon.
8. When normal cleaning,the steam head
has big rotary angle,can clean corners
nd also can clean low space.
USE AS A STEAM CLEANER IN HAND
Push Lock Catch,take the main body A out of holder A,and also take out the power cord.
Install the accessory adaptor at the top of main body A,until it into place.
Press salient point at the accessory adaptor to remove the accessory adaptor from main body
A
Choose the appropriate accessories(check accessories use list),according to arrow indicator to
align and implant to accessory adaptor G,then turn anticlockwise,until it into place.
Page 6 of 10
rotation,fill 360ML water use Measuring cup,
and then clockwise rotation to close water tank cup 5.
Method two
：
Remove the water tank from main body,open the
water tank cup 5 by counterclockwise rotation,fill
the water tank from water faucet.,and then clockwise
rotation to close water tank cup 5.
Install the water tank 7to main body until it clicks into place.
2.Plug in the appliance to a grounded outlet.
3.When switch the appliance on,the indicator lights will turn red at the each side of water tank,it
indicate preheating.If the lights does not illuminate,please check the "troubleshooting" section for
more details.
4.It will takes approximately 25 seconds for preheating.Once the steam mop is ready to use the
water tank will glow blue.
5.When the water tank full fill with water,it can work approximately 20 minutes.If the water tank
7 without water,the indicator lights 12 will glow red,and the lights will flash to point out need to
add water
NOTICE
：
If power off during preheating or after preheating,then power again,the
appliance will repeat above preheating action.
6.Press the steam button 4 and steam button13,the steam out.
7.Add control volume by turn steam control knob 8
clockwise
，
and counterclockwise to reduce
，
User
can adjust steam volume according different objects
NOTICE
：
steam volume control by PCB,It will takes 3 seconds adaptation time
when you adjust steam volume .It is normal phenomenon.
8. When normal cleaning,the steam head
has big rotary angle,can clean corners
and also can clean low space.
USE AS A STEAM CLEANER IN HAND
Push Lock Catch,take the main body A out of holder A,and also take out the power cord.
Install the accessory adaptor at the top of main body A,until it into place.
Press salient point at the accessory adaptor to remove the accessory adaptor from main body
A
Choose the appropriate accessories(check accessories use list),according to arrow indicator to
align and implant to accessory adaptor G,then turn anticlockwise,until it into place.
Page 6 of 10
OPERATION
1.Filling the water tank
Method one:
：
Open the water tank cup 5 by counterclockwise
rotation,fill 360ML water use Measuring cup,
and then clockwise rotation to close water tank cup 5.
Method two
：
Remove the water tank from main body,open the
water tank cup 5 by counterclockwise rotation,fill
the water tank from water faucet.,and then clockwise
rotation to close water tank cup 5.
Install the water tank 7to main body until it clicks into place.
2.Plug in the appliance to a grounded outlet.
3.When switch the appliance on,the indicator lights will turn red at the each side of water tank,it
indicate preheating.If the lights does not illuminate,please check the "troubleshooting" section for
more details.
4.It will takes approximately 25 seconds for preheating.Once the steam mop is ready to use the
water tank will glow blue.
5.When the water tank full fill with water,it can work approximately 20 minutes.If the water tank
7 without water,the indicator lights 12 will glow red,and the lights will flash to point out need to
add water
NOTICE
：
If power off during preheating or after preheating,then power again,the
appliance will repeat above preheating action.
6.Press the steam button 4 and steam button13,the steam out.
7.Add control volume by turn steam control knob 8
clockwise
，
and counterclockwise to reduce
，
User
can adjust steam volume according different objects
NOTICE
：
steam volume control by PCB,It will takes 3 seconds adaptation time
when you adjust steam volume .It is normal phenomenon.
8. When normal cleaning,the steam head
has big rotary angle,can clean corners
and also can clean low space.
USE AS A STEAM CLEANER IN HAND
Push Lock Catch,take the main body A out of holder A,and also take out the power cord.
Install the accessory adaptor at the top of main body A,until it into place.
Press salient point at the accessory adaptor to remove the accessory adaptor from main body
A
Choose the appropriate accessories(check accessories use list),according to arrow indicator to
align and implant to accessory adaptor G,then turn anticlockwise,until it into place.
Page 6 of 10
Veranderen van de accessoires
De Clever Clean ViralOff® Steam Broom kan ook gebruikt worden als manuele stoomreiniger en wordt geleverd met een
breed scala aan accessoires. Zo kunt u zelfs moeilijk bereikbare plaatsen en voorwerpen reinigen waarvoor de stoomvoet niet
geschikt is.
1. Druk op de vergrendelknop [6] om de hoofdeenheid [A] van de houder [B] te ontgrendelen. De stoombezem kan nu
worden gebruikt als een praktische handstoombezem.
2. Duw de adapter voor accessoires [F] op het apparaat totdat deze vastklikt.
3. Plaats het gewenste accessoire op de adapter [F] en draai deze vast door deze met de klok mee te draaien.
4. Om het accessoire na het reinigingsproces te verwijderen, draait u het accessoire losjes tegen de klok in en trekt u het van
de adapter [F].
5. Druk op de veiligheidsknop van de adapter [F] op de achterkant van het apparaat als u de adapter [F] wilt verwijderen.
6. De hoofdeenheid [A] kan nu weer in de houder [B] worden geplaatst.
Kijk uit! De bodem van het hoofdtoestel [A] wordt tijdens het gebruik heet! Er is gevaar voor brandwonden.
Laat het hoofdtoestel [A] afkoelen voordat u het aanraakt.
