background image

17

CLEARSPAN

 CEDAR GREENHOUSES

Revision date: 06.16.09

12

INSTALL SOLAR VENT OPENER ASSEMBLY

The solar vent opener assemblies are attached to the vented roof and end panels of the greenhouse.
When properly installed, these assemblies automatically open the vent panels of the greenhouse when the 
temperature in the greenhouse increases.

NOTE:

The solar vent opener requires assembly. Follow the instructions 

included with the solar vent opener

to assemble the vent 

before

 attaching it to the greenhouse. After the vent opener is assembled, continue 

with the these instructions.

Verify that the vent panel on the greenhouse opens easily and is not obstructed.

1.

Choose one of the assembled solar vent openers and attach it to the greenhouse frame and the vent 

2.

panel as shown in the diagram. Secure using 1-1/8" FAS8 construction screws. 

NOTE:

Attach the opener near the middle of the vent panel. Verify that nothing interferes with the 

operation of the solar vent opener.

Repeat for each vent.

3.

Check the operation of the panels and the installed openers and consult the documentation

4.

 included 

with the opener

 for opener maintenance and winter storage.

View as 
seen from 
the inside.

Vent

Panel

Actual greenhouse may differ from what is shown above.

Содержание 104895
























Отзывы: