manualshive.com logo in svg

Clearfield StreetSmart Pre-Assigned FDH, Руководство по установке, Страница: 3 / 17

Поделиться
Скачать
Clearfield StreetSmart Pre-Assigned FDH Скачать руководство пользователя страница 3

3

StreetSmart Pre-Terminated FDH Cabinet

__________________________________________________________

Installation Manual

Direct: 763.476.6866 • National: 800.422.2537 • www.SeeClearfield.com • [email protected] 

Manual 021814 REV A - Jan 2021

Application

Technical Specifications

StreetSmart Pre-Terminated FDH Cabinet

Dimensions

22.72” T x 15.47” W x 14.18” D (577.08mm T x 393.94mm W x 360.17mm D) * Without Riser

Weight

40 lbs. (18.14 kg)

Dist. Port Density

144 or 288

Max. Feeder/Express Ports

12 or 24

Cable Entrances

4

Mounting Options (Hoist kits

included with each cabinet)

Vault mount; pole mount; pad mount

Riser Base

6”; 8 lbs (127 mm; 2.72 kg)

12”; 12 lbs. (304.80 mm; 5.44 kg)

Pre-loaded WaveSmart High

Density Splitters with 900um Legs

4 or 8

Splitter Staging Capacity

72

Connector Modules

12 Pack Adapter Modules

Connector Types

SC/UPC, SC/APC

Cable Types

Indoor/Outdoor, Outdoor, Outdoor Armored, Ribbon and Loose Tube

Door Locks

2 per door

Venting

Built-in Replaceable Roof Vent

Material

0.90 (2.286 mm) Aluminum with almond powder coating

Clearfield’s StreetSmart Pre-Assigned FDH PON Cabinet provides an interconnect 

environment from the feeder network through the passive optical splitter to the 

distribution network.

Designed for rapid PON Network deployments, these cabinets provide a single 

distribution point to deploy FTTH in large scale MDU’s, urban or dense neighbor

-

hoods. Pre-Assigned WaveSmart High Density 1 x 32 Splitters are loaded into the 

cabinet with a pre-terminated fiber tail, making installation and deployment very 

cost and time effective.

Description

The StreetSmart Pre-Assigned FDH PON Cabinet provides a turn-key solution for up to 288 distribution fibers for an outside 

plant FTTx PON application. WaveSmart High Density 1 x 32 Splitters are installed and pre-assigned into Clearfield’s 12 

pack SC/APC module adapters, allowing the service provider to instantly turn-up revenue-generating circuits.

The StreetSmart 288 PON Cabinet incorporates a cross-cut roof designed to shed water and includes a roof/solar shield 

and a reusable/replaceable venting feature, providing additional protection for deployed fiber. The outer shell of the cabinet 

is replaceable, allowing the cabinet to be repaired if damaged. Mounting options include pad, pole or vault mounted with 

either a 6” or 12” riser.

Содержание StreetSmart Pre-Assigned FDH


















Отзывы:

Нет отзывов