Clear-Com Eclipse Median страница 44 Скачать руководство пользователя

Страница: 44 / 114

Vitec Group Communications

Eclipse Median Instruction Manual

3 - 4

Primary Link Status LEDs

These LEDs indicate the status and functioning of the primary (A) fiber
optic link.

Link LED

This LED indicates whether a link has been established on the primary
fiber optic circuit (transceiver A). When illuminated a link is present.

TXVR LED

This LED indicates when data is being transmitted on the primary
circuit. It is illuminated when data is present on the circuit.

ACT LED

This LED is lit if the primary fiber optic circuit is active.

ERR LED

This LED will be illuminated if an error condition is detected on the
primary fiber optic circuit.

Secondary Link Status LEDs

These LEDs indicate the status and functioning of the secondary (B)
fiber optic link.

Link LED

This LED indicates whether a link has been established on the
secondary fiber optic circuit (transceiver A). When illuminated a link is
present.

TXVR LED

This LED indicates when data is being transmitted on the secondary
circuit. It is illuminated when data is present on the circuit.

ACT LED

This LED is lit if the secondary fiber optic circuit is active.

ERR LED

This LED will be illuminated if an error condition is detected on the
secondary fiber optic circuit.

Status LED

The green “frame data” LED illuminates to indicate successful
communication between the fiber master card and the CPU card. The
status LED on the slave fiber card does not light.

Содержание Eclipse Median



















































































































Результаты поиска

Содержание Eclipse Median

Отзывы:

Похожие инструкции для Eclipse Median

Бренды по названию

Популярные бренды

Clear-Com Eclipse Median, Инструкция по эксплуатации

Результаты поиска

Содержание Eclipse Median

Отзывы:

Похожие инструкции для Eclipse Median

Бренды по названию

Популярные бренды