32 | nORD WAVe 2 useR MAnuAL Os V1.0x
sOunD Menu
Hold
SHIFT
and press
SOUND
(Program 2) to access the sound menu.
use the
PAGE
3
and
4
buttons to navigate between the various menu
items on the sound menu. The
VALUE
dial is used to change settings,
and soft buttons to access additional settings (as described above),
where applicable. Press
EXIT
(shift) to leave the menu.
1 - GLOBAL TRAnsPOse
This setting allows for transposing the entire nord Wave 2 in semitone
steps. This setting will be
added
to any on-panel transpose value stored
with a program.
Range: +/- 6 semitones (default value is “none”)
2 - FIne Tune
Fine Tune can be used to fine tune the pitch of the nord Wave 2 in finer
increments.
Range: +/- 50 Cents (+/- half a semitone). Default value is “0”
3 - VIBRATO
RATe
This setting determines the rate of the Vibrato.
Range: 4.00 - 8.00 Hz (Default 5.5 Hz)
AMnT (AMOunT)
This determines the amount of Vibrato when one of the vibrato
delay
modes are used.
Range: 0-50 cent (Default value is 22 cent)
MIDI Menu
Hold
SHIFT
and press
MIDI
(Program 3) to access the MIDI menu set-
tings. use the
PAGE
3
and
4
buttons to navigate between the various
menu items on the MIDI menu. The
VALUE
Dial is used to change set-
tings. soft buttons are used to access additional settings where applica-
ble. When you are done, press exit (shift) to exit the menu.
1 - LOCAL COnTROL
MIDI Local control determines if the nord Wave 2 keyboard and front
panel controls should control internal instruments and programs or only
transmit MIDI. Local On is the normal “play mode”. In Local Off mode,
front panel and keyboard actions are transmitted via MIDI only.
Range: On (Default), Off
M
Local always defaults back to “On” every time the Nord Wave 2 is
powered on.
2 - MIDI GLOBAL CHAnneL
This sets the transmitting and receiving MIDI channel for the Global
Channel. The Global Channel transmits all keyboard, pedal and panel
actions as MIDI signals. It can also be used as a receiving channel with
full control of the entire Wave 2. When set to
Off
, the text “send on Lay-
er Channel” is displayed, indicating that the Layer Channels in this mode
can be used for
sending
MIDI.
Range: 1-16, Off (Default 1)
3 - MIDI LAYeR A / B / C / D CHAnneL
When a Global MIDI channel is set, i.e. not set to Off, this page defines
the
receiving
MIDI channels for Layers A/B/C/D.
When the Global MIDI channel is set to Off, the channels defined on this
page will both send and receive MIDI, and are stored per-program. In
this scenario a store operation needs to be performed for the settings to
be recalled when the program is loaded again.
Range: 1-16, Off (Default Off)
4 - CC / PC / PC-seL / PBenD MODe
CC (COnTROL CHAnGe)
This allows you to set if you want your nord Wave 2 to transmit and/or
receive MIDI Controller Messages or not on the Global channel.
Range: Off, Send, Receive, Send & Receive (Default)
PC (PROGRAM CHAnGe)
This setting determines whether your nord Wave 2 transmits and/or
receives MIDI program Change Messages, on the Global channel.
Range: Off, Send, Receive, Send & Receive (Default)
PC-seL (PROGRAM CHAnGe seLeCT)
The Type setting determines if Program Change messages are sent only
for programs (
Programs Only
), or if they are also sent when changing
Live Programs or Oscillators selection. Read more about this on page
30.
Range: Programs Only, Extended (Default)
PBenD (PITCH BenD)
Pitch Bend Mode specifies how the nord Wave 2 handles incoming and
outgoing Pitch Bend messages, generated by the pitch stick.
Range: Off, Send, Receive, Send & Receive (Default)
5 - TRAnsPOse MIDI AT
When set to
In
, any active transpose value (global and/or set per pro-
gram) will
not
be applied to the outgoing MIDI stream, but only to incom-
ing MIDI data. If set to
Out
, any active transpose value will affect sent
MIDI notes but not incoming ones.
Range: In (Default), Out
6 - MIDI CC DuMP
From this page, a “dump” of the MIDI CC values for all panel settings
can be sent, for any of the four Layers. This can for instance be used for
initializing a sequencer track with the Layer parameters. use the dial or
the Layer A-D buttons to select the Layer to send.
Press “Dump” to send CC values for all panel parameters
Содержание Nord Wave 2
Страница 40: ......
