background image

Surface Sanding On The Sanding Belt

WARNING:  To avoid injury from slips, jams or thrown

pieces, adjust the backstop to clear the sanding

surface by no more than 1/16”. When checking

clearance between the belt and work support,

press the belt flat against the bed beneath it.

Hold the workpiece firmly with both hands,

keeping fingers away from the sanding belt.
Keep the end up against the backstop

and move the work evenly across the

sanding belt. Use extra caution when

sanding very thin pieces.
For sanding long pieces, remove the work support.
Apply only enough pressure to allow the sanding belt to remove

material.

It is more convenient to sand the ends of long work-

pieces with sanding belt in a vertical position.
See “Basic Operation - Positioning Belt Bed” for

adjusting the belt bed, and see “Assembly -

Installing Table Assembly” for adjusting worktable.
Move the work evenly across the sanding belt. For

accuracy, use a mitre gauge.

Sanding Curved Edges

End Sanding On The Sanding Belt

Always sand inside curves on the idler

pulley as shown.

WARNING:

Never attempt to sand

the ends of a workpiece on the idler

pulley. Applying the end of the

workpiece to the idler pulley could

cause the workpiece to fly up and

result in an injury.

16

Содержание Woodworker CS4-6C
























Отзывы: