Clarke American 8 07032C Скачать руководство пользователя страница 7

Страница: 7 / 30

Clarke

American Sanders American 8 Floor Sander Operator's Manual

Page 7

How to Transport the Machine

WARNING:

The machine is heavy. Remove the

motor from the machine before trans-

porting. Get help loading the machine

and motor.

To transport the machine, follow this procedure:

1. Make sure the power cable is disconnected from the

electrical outlet.

2. Disconnect the handle plug connection. See figure 1.

3. Remove the belt cover.

4. Remove the fan belt.

5. Loosen the motor bolt. Using the ¾” wrench, turn the motor

bolt counterclockwise.

6. Using the

” wrench, remove the two hex

nuts (1).

7. Lower the motor locating screws (2). To lower the motor

locating screws, turn the screws clockwise. Make sure the

screws are aligned with the openings at the front of the

motor platform. See

figure 2.

8. Slide the motor forward.

9. Remove the drive belt.

10. Remove the motor from the chassis.

To re-assemble the machine after transporting, follow this

procedure:

1. Reposition motor on chassis.

2. Install the drum belt. Slide the motor back until adequate

tension is achieved in belt.

CAUTION: To prevent damage to the floor

surface, make sure the drive belt is

tight.

3. Resecure the motor to the chassis.

4. Install the fan belt.

5. Install the belt cover.

6. Reconnect the handle plug.

Figure 1

Figure 2

Содержание American 8 07032C































Результаты поиска

Содержание American 8 07032C

Отзывы:

Похожие инструкции для American 8 07032C

Бренды по названию

Популярные бренды

Clarke American 8 07032C, Руководство оператора

Результаты поиска

Содержание American 8 07032C

Отзывы:

Похожие инструкции для American 8 07032C

Бренды по названию

Популярные бренды