Clarke American 8 07032C Скачать руководство пользователя страница 1

Страница: 1 / 30

Part No. LT069200 3/14

American 8

Operator's Manual

Active Model: 07105A

Obsolete Models: 07032C, 07048C, 07106A

READ THIS BOOK

This book has important information for the use and safe operation of this machine. Failure to read this book prior to operating or

attempting any service or maintenance procedure to your Clarke American Sanders machine could result in injury to you or to other

personnel; damage to the machine or to other property could occur as well. You must have training in the operation of this machine

before using it. If your operator cannot read this manual, have it explained fully before attempting to operate this machine.

Si Ud. o sus operadores no pueden leer el Inglés, se hagan explicar este manual completamente antes de tratar el manejo o

servicio de esta máquina.

All directions given in this book are as seen from the operator’s position at the rear of the machine.

Содержание American 8 07032C































Результаты поиска

Содержание American 8 07032C

Отзывы:

Похожие инструкции для American 8 07032C

Бренды по названию

Популярные бренды

Clarke American 8 07032C, Руководство оператора

Результаты поиска

Содержание American 8 07032C

Отзывы:

Похожие инструкции для American 8 07032C

Бренды по названию

Популярные бренды