background image

3

GENERAL SAFETY RULES 

1.

ALWAYS 

learn the machines applications, limitations and the specific 

potential hazards. Read and become familiar with the entire operating 
manual.

1.

ALWAYS 

use a face or dust mask if the operation is particularly dusty.

2.

AlWAYS 

check for damage before using the machine, check for alignment 

of moving parts, breakage of parts, and any other condition that may 
affect the machines operation. Damage should be properly repaired or 
the part replaced. If in doubt, 

DO NOT

 use the machine. Consult your local 

dealer.

3.

ALWAYS 

disconnect the machine from the power supply before servicing 

and when changing accessories. 

4.

ALWAYS 

wear safety goggles, manufactured to the latest European Safety 

Standards. Everyday eyeglasses do not have impact resistant lenses, and 
are not safety glasses.

5.

ALWAYS 

keep work area clean. Cluttered areas and benches invite 

accidents.

6.

ALWAYS 

ensure that adequate lighting is available. Ensure that lighting is 

placed so that you will not be working in your own shadow.

7.

ALWAYS 

keep children away. All visitors should be kept a safe distance from 

the work area, especially when the machine is being used.

8.

ALWAYS 

maintain machine in top condition. Keep tools/machines clean for 

the best and safest performance. Follow maintenance instructions.

9.

ALWAYS 

handle with extreme care and do not carry the tool/machine by its 

electric cable, or pull on the cable to disconnect it from the power supply.

10.

ALWAYS 

ensure the switch is off before plugging in to mains. Avoid 

accidental starting.

11.

ALWAYS 

concentrate on the job in hand, no matter how trivial it may seem. 

Be aware that accidents are caused by carelessness due to familiarity.

12.

ALWAYS 

keep your proper footing and balance at all times - don’t 

overreach. For best footing, wear rubber soled footwear. Keep floor clear 
of oil, scrap wood, etc.

13.

ALWAYS 

dress properly. Loose clothing or jewellery may get caught in 

moving parts. Wear protective hair covering to contain long hair.

14.

ALWAYS 

guard against electric shock. Avoid contact with earthed surfaces 

- pipes, radiators etc.

Содержание 6500413





















Отзывы: